Mitsubishi Electric MELIPC MI5000 Series, User Manual

Share

Page: 95 / 320

Mitsubishi Electric MELIPC MI5000 Series User Manual Download Page 95

7 CC-Link IE Field Network Basic FUNCTION

7.4 Processing Time

93

7

7.4

Processing Time

The CC-Link IE Field Network Basic processing time comprises the following.
• Link scan time + slave station response processing time = transmission delay time

Link scan time

This product operates according to a link scan time that is set in "Link Scan Time Settings" of "CC-Link IEF Basic Setting".
(

Page 162 Basic Parameter List)

Link scan time check

Link scan time maximum, minimum, and current values can be confirmed using the following method.
• CC-Link IE Field Network Basic diagnosis(



Page 90 CC-Link IE Field Network Basic diagnostics)

• Buffer Memory (



Page 282 List of Buffer Memory)

(1) Master station
(2) Slave station
(3) Link device
(4) Link scan time
(5) Slave station response processing time

(3)

(1)

(4)

(2)

(3)

(5)

«
...
93
94
95
96
97
...
»

Summary of Contents for MELIPC MI5000 Series

































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands