manualshive.com logo in svg

Mitsubishi Electric MELIPC MI5000 Series, User Manual

Share
Download
Mitsubishi Electric MELIPC MI5000 Series User Manual Download Page 3

1

SAFETY PRECAUTIONS

(Read these precautions before using this product.)
Before using this product, please read this manual and the relevant manuals carefully and pay full attention to safety to handle 
the product correctly.
The precautions given in this manual are concerned with this product only.
In this manual, the safety precautions are classified into two levels: "

WARNING" and "

CAUTION".

Under some circumstances, failure to observe the precautions given under "

CAUTION" may lead to serious 

consequences.
Observe the precautions of both levels because they are important for personal and system safety.
Make sure that the end users read this manual and then keep the manual in a safe place for future reference.

[Design Precautions]

WARNING

●

Configure safety circuits external to the product to ensure that the entire system operates safely even 
when a fault occurs in the external power supply or the product. Failure to do so may result in an 
accident due to an incorrect output or malfunction.
(1) Emergency stop circuits, protection circuits, and protective interlock circuits for conflicting 

operations (such as forward/reverse rotations or upper/lower limit positioning) must be configured 
external to the product.

(2) When the product detects an abnormal condition, it stops the operation and all outputs are:

 • Turned off if the overcurrent or overvoltage protection of the power supply module is activated.
 • Held or turned off according to the parameter setting if the self-diagnostic function of the 

product detects an error such as a watchdog timer error.

●

Configure a circuit so that the product is turned on first and then the external power supply. If the 
external power supply is turned on first, an accident may occur due to an incorrect output or 
malfunction.

●

For the operating status of each station after a communication failure, refer to manuals relevant to the 
network. Incorrect output or malfunction due to a communication failure may result in an accident.

●

Before performing operations for the product from the peripheral connected, read the relevant 
manuals carefully and ensure the safety.

WARNING

Indicates that incorrect handling may cause hazardous conditions, resulting in 

death or severe injury. 

CAUTION

Indicates that incorrect handling may cause hazardous conditions, resulting in 

minor or moderate injury or property damage.

Summary of Contents for MELIPC MI5000 Series

































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands