Mitsubishi Electric MELIPC MI5000 Series, User Manual

Share

Page: 111 / 320

Mitsubishi Electric MELIPC MI5000 Series User Manual Download Page 111

8 DIAGNOSTIC AND MAINTENANCE FUNCTIONS

8.3 Operating Status Management Function

109

8

Fan module cleaning detection function

This function detects the operating status of the fan module.
The time for which the power supply of this product is ON is counted, and the arrival of the fan module cleaning interval is
reported after a fixed time has passed.

Notification check

When the fan module cleaning interval is reached, the following operations are executed.
• The event (fan module filter cleaning notification) is saved to the event history. (



Page 253 Event List)

• The FAN LED turns ON.

*1

(



MELIPC MI5000 Series User's Manual (Startup))

*1 When this function turns on the FAN LED, the FAN LED does not turn off even when the power supply of this product is turned OFF to

ON or the product is reset. Start this product in off-line mode, and then execute [Alert reset]. After executing [Alert reset], the event (fan
module filter cleaning complete) is saved to the event history.

Precautions

If the fan module is cleaned or replaced, always execute [Alert reset] by using a menu operation. Otherwise, the next cleaning
interval for the fan module will be counted incorrectly.

«
...
109
110
111
112
113
...
»

Summary of Contents for MELIPC MI5000 Series

































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands