manualshive.com logo in svg

Mitsubishi Electric MELIPC MI5000 Series, User Manual

Share
Download
Mitsubishi Electric MELIPC MI5000 Series User Manual Download Page 75

6  CC-Link IE Field Network FUNCTION

6.5  Processing Time

73

6

Transmission delay time of cyclic transmission

This section shows the transmission delay time of cyclic transmission.

When the local station is a C Controller module, change SL to the following processing time.
  • SL=P=R+

α

P: Processing time on a C Controller system
R: Refresh cycle

α

: Link refresh time

When the local station is this product, use direct access to the link device or buffer memory access. Change 
SL to the processing time of the function.

In case of a master station and intelligent device station / remote device station

■

Master station (RX, RWr) 

←

 intelligent device station/remote device station (input)

Times are shown below.
 • The time from signal input into the intelligent device station / remote device station until the link device of the master station 

is turned ON or OFF

 • The time from data input into the intelligent device station / remote device station until data is stored in the link device of the 

master station

CT: Synchronous communication cycle
Rio: Processing time of intelligent device station / remote device station (

Manual of intelligent device station / remote 

device station being used)

■

Master station (RY, RWw) 

→

 intelligent device station/remote device station (output)

Times are shown below.
 • The time from when the link device of the master station is turned ON or OFF until the output of the intelligent device station 

/ remote device station is turned ON or OFF.

 • The time from data setting to the link device of the master station until data is output to the intelligent device station / remote 

device station

CT: Synchronous communication cycle
Rio: Processing time of intelligent device station / remote device station (

Manual of intelligent device station / remote 

device station being used)

Calculated value

Transmission delay time (no block data assurance per station setting)

Normal value

(CT

×

1)+Rio

Maximum value

(CT

×

2)+Rio

Calculated value

Transmission delay time (no block data assurance per station setting)

Normal value

(CT

×

1)+Rio

Maximum value

(CT

×

2)+Rio

Summary of Contents for MELIPC MI5000 Series

































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands