manualshive.com logo in svg

Mitsubishi Electric MELIPC MI5000 Series, User Manual

Share
Download
Mitsubishi Electric MELIPC MI5000 Series User Manual Download Page 110

108

8  DIAGNOSTIC AND MAINTENANCE FUNCTIONS
8.3  Operating Status Management Function

Momentary power failure detection function

This function detects momentary power failures when the input voltage supplied to the power supply module is below the 
prescribed range during operation of this product.

Operation at momentary power failure

The following section shows operation during a momentary power failure.

■

When a momentary power failure shorter than the allowable time is detected

 • The buffer memory values are retained when a momentary power failure occurs.
 • The error information is recorded in the event history after power is restored. (During the initial detection)
 • The number of momentary power failures is retained internally. (

 Page 108 Check of the number of momentary power 

failure detections)

■

When a momentary power failure exceeding the allowable momentary power failure time is 

detected

This product enters the same state as when the following operations are performed.
 • Turning the power OFF and ON or resetting the product (

MELIPC MI5000 Series User's Manual (Startup))

 • Resetting the product by the MELIPC RESET/WIN RESET switch (

MELIPC MI5000 Series User's Manual (Startup))

 • Resetting the product by a remote operation of MI Configurator (

 Page 104 Remote operation function)

 • Resetting the product by the C Controller module dedicated function (CCPU_Reset) (

MELIPC MI5000 Series 

Programming Manual (VxWorks))

Check of the number of momentary power failure detections

This product retains internally the number of momentary power failure detections.
The number of detected momentary power failures can be checked by the C Controller module dedicated function 
(CCPU_GetPowerStatus).

■

Function list

For details on the C Controller module dedicated functions, refer to the following manual.

MELIPC MI5000 Series Programming Manual (VxWorks)

Function name

Description

CCPU_GetPowerStatus

Acquires the power supply status of a MELIPC.

Summary of Contents for MELIPC MI5000 Series

































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands