Mitsubishi Electric MELIPC MI5000 Series User Manual Download Page 243

Page: 243 / 320

APPX

Appendix 2 List of Error Codes

241

■

CC-Link IE Field Network Basic error codes (C000H to CFFFH)

The following shows the codes for errors that occur on CC-Link IE Field Network Basic.

Error code

Error name

Description

Corrective action

CFC0H

Cyclic transmission error (master
station)

Unable to execute cyclic transmission
because multiple master stations exist in
the same network address.

Check the existence status of master
station in network.

CFC1H

Cyclic transmission error (master
station)

Unable to execute cyclic transmission
because the error occurred in cyclic
transmission.

• Take measures to reduce noise.
• If, after running this, the same error is

displayed again, consult your local
Mitsubishi representative.

CFC8H

Cyclic transmission error (master
station)

Unable to execute cyclic transmission
because the slave station controlled by
other master station exists.

• Check the existence status of master

station in network.

• Check the slave station where the error

occurred.

CFC9H

Cyclic transmission error (master
station)

Unable to execute cyclic transmission
because the slave station of the same IP
address exists in the same network
address.

• Check the existence status of slave

station in network.

• Check the slave station where the error

occurred.

CFD0H

Master station error

The port No. (61450) used in CC-Link IE
Field Network Basic has already been used.

Check the port No. used in the external
device configuration.

CFD1H

Master station error

Invalid value has been set in subnet mask.

Check the parameter setting.

CFE0H

Cyclic transmission error (slave
station)

The cyclic transmission was executed for
the slave station controlled by other master
station.

• Check the existence status of master

station in network.

• Check the slave station where the error

occurred.

CFE1H

Cyclic transmission error (slave
station)

The unusable number of occupied stations
has been specified from master station.

Check the number of occupied stations
setting in master station parameter
(Network Configuration Settings).

CFE8H

Cyclic transmission error (slave
station)

There is no response from slave station.

• Check the slave station disconnection

detection setting in master station
parameter (Network Configuration
Settings).

• Check the existence status of slave

station in network.

• Check the slave station which is

disconnected.

• Take measures to reduce noise.

CFE9H

Cyclic transmission error (slave
station)

The slave station of the same IP address
has existed in the same network address.

Check the slave station where the error
occurred.

CFF0H

Slave station error

The error occurred in slave station.

Check the slave station where the error
occurred.

Summary of Contents for MELIPC MI5000 Series

































































































































































































































































































































Search results

Summary of Contents for MELIPC MI5000 Series

Reviews:

Brands by name

Popular brands

Mitsubishi Electric MELIPC MI5000 Series, User Manual

Search results

Summary of Contents for MELIPC MI5000 Series

Reviews:

Brands by name

Popular brands