Mitsubishi Electric MELIPC MI5000 Series User Manual Download Page 190

Page: 190 / 320

188

18 APPRICATION PARAMETERS
18.1 CC-Link IE Field Network Parameters List

Displayed items

■

Station type settings

■

Network number settings

■

Station number settings

Item

Description

Setting range

Parameter
No.

Station type

Select the CC-Link IE Field Network function station type (network
type).

• Master station
• Local station

7100H
7700H

Item

Description

Setting range

Parameter
No.

Network No.

Set the network No. for the network to connect to the CC-Link IE Field
Network.

1 to 239
(Default: 1)

7100H

Item

Description

Setting range

Parameter
No.

Station number settings method

Select the station number configuration method of local stations. (Local
station only setting)

Set in parameters

7100H

Station number

Set the CC-Link IE Field Network station number.

1 to 120
(Default: 1)
(Master station fixed at
"0")

Summary of Contents for MELIPC MI5000 Series

































































































































































































































































































































Search results

Summary of Contents for MELIPC MI5000 Series

Reviews:

Brands by name

Popular brands

Mitsubishi Electric MELIPC MI5000 Series, User Manual

Search results

Summary of Contents for MELIPC MI5000 Series

Reviews:

Brands by name

Popular brands