Mitsubishi Electric MELIPC MI5000 Series User Manual Download Page 225

Page: 225 / 320

APPX

Appendix 2 List of Error Codes

223

1848H

Power supply temperature error

Internal temperature abnormality has been
detected in the power supply module.

Reset the system. If the same error is
displayed again, this may indicate a
hardware fault. Consult your local Mitsubishi
representative.

1849H

MELIPC temperature error

A MELIPC temperature error was detected.

If this problem is not resolved, a hardware
error may result from a temperature error.
Take the following measures.

• Check the ambient temperature.
• Check that the vent of the MELIPC is not

blocked.

• Inspect and clean the fan module.
• Replace the fan module. If the same error

is displayed again, this may indicate a
hardware fault. Consult your local
Mitsubishi representative.

• Replace the fan module.
• Take measures to reduce the

temperature.

• If the same error is displayed again, this

may indicate a hardware fault. Consult
your local Mitsubishi representative.

184AH

Number of CFast card writes
exceeded

The number of writes to the CFast card
exceeded 10,000. (Number of writes >
10,000)

Replace the CFast card.

184BH

Power supply temperature sensor
fault

A temperature sensor fault in the power
supply module has been detected.

Reset the system. If the same error is
displayed again, this may indicate a
hardware fault. Consult your local Mitsubishi
representative.

184CH

USB port fault

An overcurrent to the USB port has been
detected.

• Replace the USB.
• Reset the system. If the same error is

displayed again, this may indicate a
hardware fault. Consult your local
Mitsubishi representative.

184DH

CFast card error

An overcurrent to the CFast card has been
detected.

• Replace the CFast card
• Reset the system. If the same error is

displayed again, this may indicate a
hardware fault. Consult your local
Mitsubishi representative.

184EH

CFast card error

Insertion/removal of the CFast card has
been detected.

Reset the system. If the same error is
displayed again, this may indicate a
hardware fault. Consult your local Mitsubishi
representative.

184FH

DisplayPort error

An overcurrent to the DisplayPort has been
detected.

• Review the DisplayPort connection.
• Reset the system. If the same error is

displayed again, this may indicate a
hardware fault. Consult your local
Mitsubishi representative.

1850H

Windows part stop

A stop (no response) condition such as a
Windows blue screen is detected.

• Review the software applications on the

Windows part.

• Review the devices of the Windows part.
• Review the user programs of the

Windows part.

• Restart the Windows part.
• If the issue is still not resolved, replace

the MELIPC.

1851H

CFast card error

An error has been detected in the CFast
card.

• Replace the CFast card.
• Take measures to reduce noise.
• Reset the system. If the same error is

displayed again, this may indicate a
hardware fault. Consult your local
Mitsubishi representative.

1852H

CFast card error

An error has been detected in the CFast
card.

Replace the CFast card.

20E0H

Invalid power supply module

A power supply module that cannot be
recognized was detected.

Mount only applicable power supply
modules.

2160H

IP address overlap error

An IP address overlap was detected.

Check the IP address of the Ethernet port
(CH1).

Error code

Error name

Description

Corrective action

Summary of Contents for MELIPC MI5000 Series

































































































































































































































































































































Search results

Summary of Contents for MELIPC MI5000 Series

Reviews:

Brands by name

Popular brands

Mitsubishi Electric MELIPC MI5000 Series, User Manual

Search results

Summary of Contents for MELIPC MI5000 Series

Reviews:

Brands by name

Popular brands