manualshive.com logo in svg

Mitsubishi Electric MELIPC MI5000 Series, User Manual

Share
Download
Mitsubishi Electric MELIPC MI5000 Series User Manual Download Page 118

116

8  DIAGNOSTIC AND MAINTENANCE FUNCTIONS
8.5  Switch/LED Operation Function

LED status acquisition function

This function acquires the statuses of the main LED, dot matrix LED, and the CC-Link IE Field Network LED of this product.
The following table shows the LEDs for which LED statuses can be acquired.

: Possible, 

: Impossible

LED status acquisition

Acquire the LED statuses using the C Controller module dedicated functions (CCPU_GetLEDStatus, 
CCPU_GetDotMatrixLED, CCPU_GetDotMatrixLED_ISR).

■

Function list

For details on the C Controller module dedicated functions, refer to the following manual.

MELIPC MI5000 Series Programming Manual (VxWorks)

LED name

Acquisition 
applicability

MAIN LED

VX RDY LED

WIN RDY LED

MAIN ERR LED

MAIN RUN LED

STORAGE LED

FAN LED

INFO LED

RS SD/RD LED

BATTERY LED

CC-Link IE Field Network LED

RUN LED

ERR LED

MST LED

D LINK LED

SD/RD LED

L ERR LED

Dot matrix LED

Function name

Description

CCPU_GetLEDStatus

Acquires the LED status of a MELIPC.

CCPU_GetDotMatrixLED

Acquires the values displayed on the dot matrix LED of a MELIPC.

CCPU_GetDotMatrixLED_ISR

Summary of Contents for MELIPC MI5000 Series

































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands