manualshive.com logo in svg

Mitsubishi Electric MELIPC MI5000 Series, User Manual

Share
Download
Mitsubishi Electric MELIPC MI5000 Series User Manual Download Page 44

42

6  CC-Link IE Field Network FUNCTION
6.1  Cyclic Transmission

 • At input from slave station

 The slave station link device (RX, RWr) status is output to external devices.

 The slave station link device (RX, RWr) status is stored in the master station link device (RX, RWr) using link scan.

 The master station link device (RX, RWr) status is read by a user program.

 • At output from master station

 The master station link device (RY, RWw) status is changed by a user program.

 The master station link device (RY, RWw) status is stored in the slave station link device (RY, RWw) using link scan.

 The slave station link device (RY, RWw) status is output to external devices.

Summary of Contents for MELIPC MI5000 Series

































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands