Mitsubishi Electric CC-Link IE Field NZ2GF12A-60IOLH8 User Manual Download Page 59 | Manualshive

Page: 59 / 162

background image

6 Parameter Setting

6.4 IO-Link Device Parameter Setting

57

6

6.4

IO-Link Device Parameter Setting

Using CommDTM for IO-Link master module in FDT, IO-Link device parameters can be read or written and data can be
monitored via the IO-Link module. In addition, multiple IO-Link devices can be managed from one place. IODD can be
converted to Device DTM using IODD DTM Configurator. IODD is supplied from the sensor manufacturer.

Setting procedure when FDC and CommDTM are used

The following describes how to set the IO-Link device parameter.

Setting procedure

1.

Install IODD using the installer supplied from the manufacturer of the sensor. Convert IODD supplied from the sensor
manufacturer to Device DTM using IODD DTM Configurator. When Device DTM is supplied from the sensor
manufacturer, this operation is not necessary.



Page 59 Conversion procedure of IODD

2.

When GX Works3 is used, double-click the IO-Link module in the network map in GX Works3 after installing Device
DTM. When GX Works2 is used, start FDC directly.

3.

Register M_CommDTM-IOLink and Device DTM to the DTM catalog of FDC. This registration is necessary only for the
first startup. It will not be necessary for the next and subsequent startups.

«
...
57
58
59
60
61
...
»

Summary of Contents for CC-Link IE Field NZ2GF12A-60IOLH8



































































































































































Reviews:

No comments

Related manuals for CC-Link IE Field NZ2GF12A-60IOLH8

Brand: ABB Pages: 2

Brand: Samson Pages: 56

Brand: Hach Pages: 128

Brand: Yamato Pages: 33

Brand: Gardena Pages: 18

VLT Micro Drive FC 51 Series

Brand: Danfoss Pages: 23

Brand: Garmin Pages: 4

FSDrive-MV1000 Series

Brand: YASKAWA Pages: 260

Brand: YASKAWA Pages: 114

Brand: YASKAWA Pages: 20

Brand: YASKAWA Pages: 152

Brand: YASKAWA Pages: 66

Brand: YASKAWA Pages: 20

Brand: YASKAWA Pages: 17

Brand: YASKAWA Pages: 58

J1000 CIMR-JC series

Brand: YASKAWA Pages: 2

Brand: YASKAWA Pages: 58

Brand: National Instruments Pages: 78

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands