Mitsubishi Electric CC-Link IE Field NZ2GF12A-60IOLH8 User Manual Download Page 58

Page: 58 / 162

6 Parameter Setting
6.3 Changing the IO-Link Module Parameters

Setting via a program

This section describes the procedure for changing the parameter.

Changing the network configuration

Power on and off the module.

Connect the modules again according to the desired network configuration.

Power on the module.

Perform the following steps 1 to 3.



Page 50 Setting via a program

Changing the parameters without changing the network configuration

Use an RIWT instruction to set parameters to change.

For details on parameters and the procedure for setting parameters, refer to the following.



Page 83 Data that can be read and written in transient transmission



Page 101 Program Example of Setting Parameters Using a Dedicated Instruction

Turn on Initial processing completion flag (RWw0.b8).

Check that the Initial processing request flag (RWr0.b8) is turned off and there is no initial processing request. After the
check, turn off Initial processing completion flag (RWw0.b8).

Check that Remote READY (RWr0.b11) is turned on.

Summary of Contents for CC-Link IE Field NZ2GF12A-60IOLH8



































































































































































Search results

Summary of Contents for CC-Link IE Field NZ2GF12A-60IOLH8

Reviews:

Related manuals for CC-Link IE Field NZ2GF12A-60IOLH8

Brands by name

Popular brands

Mitsubishi Electric CC-Link IE Field NZ2GF12A-60IOLH8, User Manual

Search results

Summary of Contents for CC-Link IE Field NZ2GF12A-60IOLH8

Reviews:

Related manuals for CC-Link IE Field NZ2GF12A-60IOLH8

Brands by name

Popular brands