Mitsubishi Electric CC-Link IE Field NZ2GF12A-60IOLH8 User Manual Download Page 40

Page: 40 / 162

5 INSTALLATION AND WIRING
5.4 Wiring of Ethernet Cable

5.4

Wiring of Ethernet Cable

This section describes wiring of Ethernet cable.

Connecting the Ethernet cable

*1 The time taken for the LINK LED to turn on after connection of the cable may vary. The LINK LED normally turns on in a few second.

However, if link-up processing is repeated due to a condition of a device on the line, the longer time may be required. If the LINK LED
does not turn on, refer to the following and take a corrective action.



Page 117 When the LINK LED is off

Power off the power supplies of the IO-Link
module and the external device.

Insert an Ethernet cable connector into the IO-
Link module. Pay attention to the connector's
direction.

Tighten the waterproof plug of the Ethernet
cable using a torque wrench. (



Page 40

Tightening torque)

Power on the power supply of the IO-Link
module.

Power on the external device.

Check that the LINK LED of the port into which
the Ethernet cable is connected is on.

Summary of Contents for CC-Link IE Field NZ2GF12A-60IOLH8



































































































































































Search results

Summary of Contents for CC-Link IE Field NZ2GF12A-60IOLH8

Reviews:

Related manuals for CC-Link IE Field NZ2GF12A-60IOLH8

Brands by name

Popular brands

Mitsubishi Electric CC-Link IE Field NZ2GF12A-60IOLH8, User Manual

Search results

Summary of Contents for CC-Link IE Field NZ2GF12A-60IOLH8

Reviews:

Related manuals for CC-Link IE Field NZ2GF12A-60IOLH8

Brands by name

Popular brands