Mitsubishi Electric CC-Link IE Field NZ2GF12A-60IOLH8 User Manual Download Page 43

Page: 43 / 162

5 INSTALLATION AND WIRING

5.5 Wiring the IO-Link Cable

5.5

Wiring the IO-Link Cable

This section describes wiring of IO-Link cable.

Connecting the IO-Link cable

• Attach waterproof caps to connector not used.
• The product specifications are satisfied only when all of waterproof plugs are installed with the

recommended connectable devices and all screws are tightened with an appropriate torque. (



Page 31

Recommended Connectable Device List)

Power off the power supply of the IO-Link
module.

Insert an IO-Link cable connector into the IO-
Link module. Pay attention to the connector's
direction.

Tighten the waterproof plug of the IO-Link
cable using a torque wrench. (



Page 42

Tightening torque)

Power on the power supply of the IO-Link
module.

Check that the CQ LED and Q LED of the
channel to which the IO-Link cable is
connected are in normal state. (



Page 15

LED names of the IO-Link module)

Summary of Contents for CC-Link IE Field NZ2GF12A-60IOLH8



































































































































































Search results

Summary of Contents for CC-Link IE Field NZ2GF12A-60IOLH8

Reviews:

Related manuals for CC-Link IE Field NZ2GF12A-60IOLH8

Brands by name

Popular brands

Mitsubishi Electric CC-Link IE Field NZ2GF12A-60IOLH8, User Manual

Search results

Summary of Contents for CC-Link IE Field NZ2GF12A-60IOLH8

Reviews:

Related manuals for CC-Link IE Field NZ2GF12A-60IOLH8

Brands by name

Popular brands