Mitsubishi Electric CC-Link IE Field NZ2GF12A-60IOLH8 User Manual Download Page 80 | Manualshive

Page: 80 / 162

background image

78

7 FUNCTIONS
7.3 Power Supply Monitoring Function

7.3

Power Supply Monitoring Function

This function checks the module/sensor power supply (US) voltage and the actuator power supply (UA) voltage, and notifies
of the status when voltage drops.
The module/sensor power supply voltage must be normal to check the actuator power supply voltage properly.

Description

If the module/sensor power supply voltage and actuator power supply voltage drop, the status can be checked with the
remote input signal (RX) and the LED indication.

For details on the remote input signal (RX), refer to the following.



Page 134 US voltage drop flag (18V or lower) (RX28)



Page 134 UA voltage drop flag (18V or lower) (RX29)



Page 134 UA voltage drop flag (11V or lower) (RX2A)

Setting procedure

This function is always enabled and parameter setting is not required.

Type

Detection condition

Remote input signal

LED indication

Module/sensor power supply (US)

18V or less

The US voltage drop flag (18V or
lower) (RX28) is ON.

The US LED is on in red.

Actuator power supply (UA)

18V or less

The UA voltage drop flag (18V or
lower) (RX29) is ON.

The UA LED flashes in red.

11V or less

The UA voltage drop flag (11V or
lower) (RX2A) is ON.

The UA LED is on in red.

«
...
78
79
80
81
82
...
»

Summary of Contents for CC-Link IE Field NZ2GF12A-60IOLH8



































































































































































Reviews:

No comments

Related manuals for CC-Link IE Field NZ2GF12A-60IOLH8

Concord express

Brand: GE Pages: 3

Brand: Aaeon Pages: 76

Brand: ECKELMANN Pages: 178

FOUNDATION 3730-5

Brand: Samson Pages: 132

Brand: Samson Pages: 68

Brand: Samson Pages: 128

Brand: Samson Pages: 68

Brand: X-POWER Pages: 24

Brand: Samson Pages: 80

Brand: Haehne Pages: 44

Brand: Scanreco Pages: 10

Brand: Teledyne Pages: 102

nERGY bluePRINT ENGCP15001

Brand: Soundoff Signal Pages: 5

Brand: Rain Bird Pages: 48

Brand: Sullair Pages: 31

Brand: Rain Bird Pages: 11

LOOPDRIVE FIM-RC

Brand: 4EVAC Pages: 2

Brand: Widex Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands