Miele G 6990 Operating Instructions Manual Download Page 71

Page: 71 / 104

Problem solving guide

Problem

Possible cause and remedy

All in-operation indica‐

tors are flashing quick‐

ly.

The warning buzzer is

sounding.

One of the following

faults appears in the

display:

Before rectifying the problem, you must:



Switch the dishwasher off using the



sensor.



Technical fault FXX

There may be a technical fault.
After a few seconds:



Switch the dishwasher back on.



Select the programme you want.



Close the door.

If the fault message appears again, there is a techni‐

cal fault.



Call Miele.



Waterproof fault

The Waterproof system has reacted.



Turn off the tap.



Call Miele.



Technical fault F78

A fault has occurred in the circulation pump.



Switch the dishwasher off for at least 30 seconds

with the



sensor.



Switch the dishwasher back on.



Select the programme you want.



Close the door.

If the fault message appears again, there is a techni‐

cal fault.



Call Miele.

Summary of Contents for G 6990









































































































Search results

Summary of Contents for G 6990

Reviews:

Related manuals for G 6990

Brands by name

Popular brands

Miele G 6990, Operating Instructions Manual

Search results

Summary of Contents for G 6990

Reviews:

Related manuals for G 6990

Brands by name

Popular brands