Miele G 6990 Operating Instructions Manual Download Page 50

Page: 50 / 104

Operation

Starting the programme



Start the programme by closing the

door.

The TimeControl in-operation indicator

light comes on to show that a pro‐

gramme has been started.
If you open the door, the message

Crockery can be added

will appear in the

display.

As long as this message is showing,

crockery can be added without com‐

promising wash results.



Water in the dishwasher may be

hot. Danger of scalding from water in

the cabinet.
Make sure you open the door very

carefully.

A programme should only be cancel‐

led in the first few minutes, if at all.

Otherwise important programme

stages could be omitted.

Display

The estimated duration of the pro‐

gramme selected appears in hours and

minutes in the display before the pro‐

gramme begins. During the programme,

the time left until the end of the pro‐

gramme is displayed.
Each programme stage is indicated by

a symbol:



Pre-wash / Soak



Main wash



Interim rinse



Final rinse



Drying



Finish

The programme duration displayed may

vary with the same programme. It is in‐

fluenced by, among other things, the

water temperature at each intake, the

reactivation process, the type of deter‐

gent, the amount of crockery and how

dirty it is.
When a programme is selected for the

first time, the display shows an average

time for a cold water intake.
The times shown in the Programme

chart refer to standard test loads and

temperatures.
Each time a programme is run, the

electronic unit takes the new conditions

into account, and calculates the time

required.

Summary of Contents for G 6990









































































































Search results

Summary of Contents for G 6990

Reviews:

Related manuals for G 6990

Brands by name

Popular brands

Miele G 6990, Operating Instructions Manual

Search results

Summary of Contents for G 6990

Reviews:

Related manuals for G 6990

Brands by name

Popular brands