Miele G 6990 Operating Instructions Manual Download Page 28

Page: 28 / 104

Before using for the first time



Add rinse aid only until it is visible in

the opening.

The rinse aid reservoir holds approx.

110 ml.



Close the flap firmly so that it clicks

into place. Otherwise water can enter

the rinse aid reservoir during a pro‐

gramme.



Wipe up any spilled rinse aid. This

prevents over-foaming occurring dur‐

ing the next programme.

You can adjust the rinse aid dosage

for best results (see "Settings menu -

Rinse aid").

Add rinse aid reminder

When the



Insufficient rinse aid

mes‐

sage appears in the display, the reser‐

voir contains sufficient rinse aid for 2 -

3 programmes only.



Add rinse aid in plenty of time.



Confirm with

The message will go out.

If you only ever use multi-function

combination products in your dish‐

washer, you can switch off both refill

reminders for salt and rinse aid if you

wish (see "Settings menu - Switching

off the refill reminders").

If you switch to using detergent that

does not contain salt or rinse aid, it

is important to remember to add

dishwasher salt and rinse aid and to

switch the reminders back on.

Summary of Contents for G 6990









































































































Search results

Summary of Contents for G 6990

Reviews:

Related manuals for G 6990

Brands by name

Popular brands

Miele G 6990, Operating Instructions Manual

Search results

Summary of Contents for G 6990

Reviews:

Related manuals for G 6990

Brands by name

Popular brands