Miele G 6990 Operating Instructions Manual Download Page 40

Page: 40 / 104

Comparison tests

Standard height with cutlery tray

Test standard:

AS/NZS 2007.1:2005, AS/NZS 2007.2:2005;

AS/NZS 6400:2005

Standard programme for en‐

ergy label comparison tests:

ECO

Capacity:



14 place settings

Detergent quantity:

32.5 g in compartment II

Rinse aid dispensing:

Setting 3

You can find information on adjusting the rinse aid dosage in the "Rinse aid"

section of this booklet.

Upper basket level:

Position:

Bottom

Jumbo cup rack

(if available):

Outer position

Loading examples

Pictures illustrating how to load the dishwasher are shown on the following pages.
Picture



: Upper basket

Picture



: Lower basket

Picture



: Cutlery tray

Do not lower or remove the basket inserts.

Remove the bottle holder from the lower basket

(if available).

Summary of Contents for G 6990









































































































Search results

Summary of Contents for G 6990

Reviews:

Related manuals for G 6990

Brands by name

Popular brands

Miele G 6990, Operating Instructions Manual

Search results

Summary of Contents for G 6990

Reviews:

Related manuals for G 6990

Brands by name

Popular brands