Miele G 6990 Operating Instructions Manual Download Page 82

Page: 82 / 104

Maintenance

Cleaning the drain pump and

non-return valve

If the water has not been pumped away

at the end of a programme, the drain

pump or the non-return valve might be

blocked. They are, however, easy to

clean.



Disconnect the dishwasher from the

mains supply. Switch off at the mains

socket and withdraw the plug.



Take the filter combination out of the

wash cabinet (see "Cleaning and care

- Cleaning the filters").



Scoop the water out of the cabinet

using a suitable container or utensil.



Press the catch for the non-return

valve inwards





Lift out the non-return valve



, and

rinse well under running water.



Remove all foreign objects from the

non-return valve.

The drain pump is situated under the

non-return valve (see arrow).



Remove all foreign objects from the

drain pump (watch out for glass or

bone splinters which are particularly

difficult to detect and could cause in‐

jury). Turn the drain pump impeller by

hand to check that there are no more

obstructions. You will feel a little re‐

sistance when you turn the impeller.



Carefully refit the non-return valve

and secure it with the catch.



Ensure that the catch engages

correctly.



Be careful not to damage any

delicate components when cleaning

the drain pump and the non-return

valve.

Summary of Contents for G 6990









































































































Search results

Summary of Contents for G 6990

Reviews:

Related manuals for G 6990

Brands by name

Popular brands

Miele G 6990, Operating Instructions Manual

Search results

Summary of Contents for G 6990

Reviews:

Related manuals for G 6990

Brands by name

Popular brands