Miele G 6990 Operating Instructions Manual Download Page 54

Page: 54 / 104

Operation

Interrupting a programme

A programme is interrupted as soon as

the door is opened.

If the door is closed again, the pro‐

gramme will continue from the point it

was at before the door was opened.



Water in the dishwasher may be

hot. Danger of scalding!
Only open the door if absolutely nec‐

essary and exercise extreme caution

when doing so. Before closing the

door again, leave it ajar for approx.

20 seconds. This will enable the tem‐

perature in the wash cabinet to set‐

tle. Then raise the door up and push

until the catch engages.

Changing a programme

If the detergent dispenser flap has

already opened, do not change the

programme.

If a programme has already started and

you wish to change it, proceed as fol‐

lows:



Open the door.



Press the Back sensor





Confirm the message

Cancel pro-

gramme?

with

Yes

The programme will be cancelled.



Select the Main menu option.

The display will revert to the main

menu.



Select the programme you want, and

then start it by shutting the door.

The In-operation indicator comes on to

show that a programme has been star‐

ted.

Summary of Contents for G 6990









































































































Search results

Summary of Contents for G 6990

Reviews:

Related manuals for G 6990

Brands by name

Popular brands

Miele G 6990, Operating Instructions Manual

Search results

Summary of Contents for G 6990

Reviews:

Related manuals for G 6990

Brands by name

Popular brands