Miele G 6990 Operating Instructions Manual Download Page 95

Page: 95 / 104

Settings menu

Sensor wash

You can adjust the

Sensor wash

pro‐

gramme so that it will remove stubborn

soiling in a lightly soiled load.



Select the setting you want and con‐

firm with

AutoOpen

At the end of programmes with a drying

phase (except

ExtraQuiet

) the door will

open automatically a little in order to

help the drying process (see "Pro‐

gramme chart").

In the

ECO

programme the door will

open during the drying phase.
This function can be deactivated if

wished.



Select the setting you want and con‐

firm with



If you have deactivated the auto‐

matic door opening function but

would still like to open the door at

the end of the programme, then

make sure that you open the door

fully. Otherwise steam from the dish‐

washer could damage the edge of

the worktop because the fan is no

longer running.

Knock2open

You can choose whether the door

should open with 1 or 2 knocks.



Select the setting you want and con‐

firm with

This function can also be disabled, in

which case the door has to be fitted

with a handle to open it.

BrilliantLight

This dishwasher has interior lighting.

When the door is open, the lighting will

switch off automatically after 15 mi‐

nutes.
The interior lighting can be switched off

permanently.



Select the setting you want and con‐

firm with

Summary of Contents for G 6990









































































































Search results

Summary of Contents for G 6990

Reviews:

Related manuals for G 6990

Brands by name

Popular brands

Miele G 6990, Operating Instructions Manual

Search results

Summary of Contents for G 6990

Reviews:

Related manuals for G 6990

Brands by name

Popular brands