Miele G 6990 Operating Instructions Manual Download Page 18

Page: 18 / 104

Caring for the environment

Energy-saving dishwashing

This dishwasher is exceptionally eco‐

nomical in its use of water and electrici‐

ty.

You can make the most of your appli‐

ance by following these tips:
– For most economical dishwashing,

make full use of the baskets without

overloading the dishwasher.

– Choose the programme to suit the

type of crockery being washed and

the degree of soiling.

– Select the

ECO

programme for ener‐

gy-saving dishwashing. This pro‐

gramme is the most efficient in terms

of its combined energy and water

consumption at cleaning normally

soiled crockery.

– If your dishwasher is connected to a

hot water supply, select the

SolarSave

programme for washing a lightly to

moderately soiled load. Because the

water is not heated in this pro‐

gramme, crockery may still be slightly

damper at the end of this programme

than it would be with other pro‐

grammes.

– Follow the detergent manufacturer's

recommendations on detergent dos‐

age.

– When using powder or liquid deter‐

gent you can use

less detergent if

baskets are only half full.

You can find further tips on energy-

saving dishwashing in "Miele's guide

to dishwashing".

Summary of Contents for G 6990









































































































Search results

Summary of Contents for G 6990

Reviews:

Related manuals for G 6990

Brands by name

Popular brands

Miele G 6990, Operating Instructions Manual

Search results

Summary of Contents for G 6990

Reviews:

Related manuals for G 6990

Brands by name

Popular brands