Miele G 6990 Operating Instructions Manual Download Page 26

Page: 26 / 104

Before using for the first time

Add salt reminder



Fill the salt reservoir with dishwasher

salt for reactivation when



Insuffi-

cient salt

appears in the display (If it

appears during a programme, wait

until the end of the programme).



Confirm with

The message will go out.



Risk of corrosion!

Immediately after filling the salt res‐

ervoir, run the

Quick wash

programme

with the

Short

programme option se‐

lected and without any crockery in

the dishwasher to remove any traces

of salt from the cabinet.

After the salt reservoir has been filled,

the refill reminder may still appear in the

display if the salt concentration has not

yet reached the correct level. If this is

the case, confirm again with

The refill reminder will be switched off if

you have programmed the dishwasher

for a water hardness below 0.9 mmol/l

(5°d - German scale).

If you only ever use multi-function

combination products in your dish‐

washer, you can switch off both refill

reminders for salt and rinse aid if you

wish (see "Settings menu - Switching

off the refill reminders").

If you switch to using detergent that

does not contain salt or rinse aid, it

is important to remember to add

dishwasher salt and rinse aid and to

switch the reminders back on.

Summary of Contents for G 6990









































































































Search results

Summary of Contents for G 6990

Reviews:

Related manuals for G 6990

Brands by name

Popular brands

Miele G 6990, Operating Instructions Manual

Search results

Summary of Contents for G 6990

Reviews:

Related manuals for G 6990

Brands by name

Popular brands