Miele G 6990 Operating Instructions Manual Download Page 11

Page: 11 / 104

Warning and Safety instructions

Technical safety



Repairs and other work by unqualified persons could be danger‐

ous. Installation, maintenance work and repairs to electrical applian‐

ces must only be carried out by a Miele approved service technician.



Before installation, check the dishwasher for visible signs of dam‐

age. Under no circumstances should you use a damaged dishwash‐

er. A damaged dishwasher could be dangerous.



The electrical safety of this appliance can only be guaranteed

when continuity is complete between it and an effective earthing

system. It is most important that this basic safety requirement is

present and regularly tested and, where there is any doubt, the elec‐

trical system in the house should be checked by a qualified electri‐

cian.

Miele cannot be held liable for the consequences of an inadequate

earthing system (e.g. electric shock).



Reliable and safe operation of this dishwasher can only be assur‐

ed if it has been connected to the mains electricity supply.



The dishwasher must only be plugged into the electricity supply

via a suitable switched socket. The electrical socket must be easily

accessible after the dishwasher is installed so that it can be discon‐

nected from the electricity supply at any time.



There must be no electrical sockets behind the dishwasher. Dan‐

ger of overheating and fire risk if the dishwasher were to be pushed

up against a plug.



The dishwasher must not be installed under a cooktop. The high

radiant temperatures which are sometimes generated by a cooktop

could damage the dishwasher. For the same reason, it should not be

installed next to open fires or other appliances which give off heat,

such as heaters etc.

Summary of Contents for G 6990









































































































Search results

Summary of Contents for G 6990

Reviews:

Related manuals for G 6990

Brands by name

Popular brands

Miele G 6990, Operating Instructions Manual

Search results

Summary of Contents for G 6990

Reviews:

Related manuals for G 6990

Brands by name

Popular brands