Miele G 6990 Operating Instructions Manual Download Page 70

Page: 70 / 104

Problem solving guide

With the help of the following guide, minor faults in the performance of the appli‐

ance, some of which may result from incorrect operation, can be put right without

contacting Miele. This will save time and money.
Please note that a call-out charge will be applied to unnecessary service visits

where the problem could have been rectified as described in these operating in‐

structions.



Unauthorised or incorrect repairs could cause personal injury or damage to

the appliance.
Repair work to electrical appliances must only be carried out by a suitably

qualified and competent person in strict accordance with current local and na‐

tional safety regulations. The manufacturer cannot be held liable for unauthor‐

ised work.

Technical problems

Problem

Possible cause and remedy

The dishwasher does

not start.

The door is not properly closed.



Raise the door upwards until the catch engages.

The appliance is not plugged in.



Insert the plug and switch on at the socket.

The mains fuse has tripped.



Reset or replace the fuse (see data plate for mini‐

mum fuse rating).

The appliance is not switched on.



Switch the dishwasher on with the



sensor.

The dishwasher stops

during a programme.

The mains fuse has tripped.



Reset or replace the fuse (see data plate for mini‐

mum fuse rating).



If the mains fuse trips again, call Miele.

After the programme

has started, the In-op‐

eration indicator light is

not visible.

The reflector panel was not correctly fitted.



Refit the reflector panel correctly (see Installation

diagram).

Summary of Contents for G 6990









































































































Search results

Summary of Contents for G 6990

Reviews:

Related manuals for G 6990

Brands by name

Popular brands

Miele G 6990, Operating Instructions Manual

Search results

Summary of Contents for G 6990

Reviews:

Related manuals for G 6990

Brands by name

Popular brands