Miele G 6990 Operating Instructions Manual Download Page 98

Page: 98 / 104

Settings menu

Volume

A sequence of audible tones will sound

at the end of the programme or if there

is a fault as long as the buzzer has

been activated.

Buzzer in the event of a fault

The buzzer in the event of a fault will

sound four times at intervals with a

short pause between each set of tones.

The buzzer which sounds when there

is a fault cannot be deactivated.

Buzzer at the end of a programme

The buzzer at the end of a programme

will sound four times at intervals with a

short pause between each set of tones.

Buzzer tones

The volume of the tone at the end of

the programme can be selected in sev‐

en stages or switched off.



Select the volume you want using the

Quieter

and

Louder

options, or switch

the buzzer off.



Confirm with

Night time buzzer tone

You can select a different volume for

the buzzer at night, or switch it off.



Select the volume you want for the

night time buzzer using the

Quieter

and

Louder

options, or switch the

night time buzzer off.



Confirm with

Night time

You can select the times for night time

to begin and end.



Select the

Start at

option.



Use the



arrow sensors to set the

time in hours and minutes for the

night time to begin and confirm both

with



Select the

Finish at

option.



Use the



arrow sensors to set the

time in hours and minutes for the

night time to end and confirm both

with

Keypad tone

An audible tone sounds each time a

sensor is pressed.
The volume for the keypad tone can be

set in seven stages, or switched off.



Select the volume you want using the

Quieter

and

Louder

options, or switch

the keypad tone off.



Confirm with

Summary of Contents for G 6990









































































































Search results

Summary of Contents for G 6990

Reviews:

Related manuals for G 6990

Brands by name

Popular brands

Miele G 6990, Operating Instructions Manual

Search results

Summary of Contents for G 6990

Reviews:

Related manuals for G 6990

Brands by name

Popular brands