Technical Information
196
G 1xxx/G 2xxx
Function Programming
Display
Extended drying time
Press the
Delay Start
button 27x. The “Delay
Start” LED flashes 2x
slowly and 7x quickly
intermittently. Press the
Start/Stop
button as
appropriate to make the
desired setting.
The "Rinse" LED is off or flashes.
The display shows
p
and a digit
alternately. Setting options:
p0
=
Normal drying time;
p1
= Extended
drying time (+10 mins).
Appliance height setting
2
Press the
Delay Start
button 36x. The “Delay
Start” LED flashes 3x
slowly and 6x quickly
intermittently. Press the
Start/Stop
button as
appropriate to make the
desired setting.
The "Rinse" LED is off or flashes.
The display shows
p
and a digit
alternately. Setting options:
p0
= Normal machine height (G
1xxx);
p1
= XXL model (G 2xxx).
Model setting
2
Press the
Delay Start
button 38x. The “Delay
Start” LED flashes 3x
slowly and 8x quickly
intermittently. Press the
Start/Stop
button as
appropriate to make the
desired setting.
The "Rinse" LED is off or flashes.
The display shows
p
and a digit
alternately. Individual setting
possibilities depend on model
and whether a circulation pump with
slide shutter (WAW) and sensor
softener (SEH) are installed as
follows:
p3
= G14xx, G24xx (without
WAW, with SEH).
Country setting
2
Press the
Delay Start
button 39x. The “Delay
Start” LED flashes 3x
slowly and 9x quickly
intermittently. Press the
Start/Stop
button as
appropriate to make the
desired setting.
The "Rinse" LED is off or flashes.
The display shows
p
and a digit
alternately. The following
countries can be set:
p1
= EUR
(Europe);
p2
= AUS (Australia);
p3
= USA;
p4
= JPN (Japan);
p5
= I/E (Italy/Spain);
p6
= SER
(Southern Europe).
3
Table 080-27:
Service Programming Mode, G 2420/G 243x
1
In machines with software version -876, run the update “Optimized cleaning of tea
residues in
Sensor Wash
program” (mat. no. 06471560). Modified threshold values will
improve the cleaning outcome.
2
If the electronic needs to be replaced during servicing, the following steps must be taken
during programming: In the first step, set the country specification and model, then switch
off the appliance. Repeat access and then set appliance width and height, and the
appropriate supply water hardness.
3
The SER country specification includes the following countries: Portugal, France, the
Netherlands, Belgium and Great Britain.
Save and quit:
Switch off the appliance.
Summary of Contents for ADVANTA G 2170
