manualshive.com logo in svg

Mercury Sable 2008, Owner'S Manual

The Mercury Sable 2008 Quick Reference Manual is a comprehensive guide to help you make the most of your vehicle. This user-friendly manual provides detailed instructions and essential information about your car's features and maintenance. Download it for free at manualshive.com and enjoy hassle-free driving with your Mercury Sable 2008.

Share
Download
background image

3. Turn the ignition switch to RUN and then back to LOCK.

4. Turn the headlamp switch to the autolamp position. The headlamps
will turn on.

5. Wait the desired amount of time for the exit delay you want (up to
three minutes), then turn the headlamp switch to

. The headlamps

will turn off.

Fog lamp control (if equipped)

With the ignition on, the fog lamps
can be turned on when the
headlamp control is pulled toward
you and is in any of the following
positions:

•

Parking lamps

•

Low beams

•

Autolamps (when active)

The fog lamps will not operate when
the high beams are active.

High beams

Push the lever toward the
instrument panel to activate. Pull
the lever towards you to deactivate.

OFF

2008 Sable

(mgo)

Owners Guide (post-2002-fmt)
USA

(fus)

Lights

83

Summary of Contents for Sable 2008









































































































































































































































































































































Reviews:

No comments

Related manuals for Sable 2008

Acdeos AXS FL Manual preview
AXS FL
Brand: Acdeos Pages: 38
DANA TM4 SUMO MD MV Installation Manual preview
TM4 SUMO MD MV
Brand: DANA Pages: 42
dallara F305 Manual preview
F305
Brand: dallara Pages: 37
Yakima BOA Installation Instructions Manual preview
BOA
Brand: Yakima Pages: 8
CITROEN C8 NaviDrive Manual preview
C8 NaviDrive
Brand: CITROEN Pages: 52
minnid 1.240.344 Operating Instructions Manual preview
1.240.344
Brand: minnid Pages: 44
DAF PACCAR PACMOBILE 20 User Manual preview
PACCAR PACMOBILE 20
Brand: DAF Pages: 18
Honda 08A06-361-210 Installation Instructions preview
08A06-361-210
Brand: Honda Pages: 4
Pro-gard SAFESTOP SS0005 Installation Manual preview
SAFESTOP SS0005
Brand: Pro-gard Pages: 4
Fab Fours VI-COWL Installation Instructions Manual preview
VI-COWL
Brand: Fab Fours Pages: 19
RAM 1500 2WD 2021 Owner'S Manual preview
1500 2WD 2021
Brand: RAM Pages: 496
Acura 08L07-TA1-203 Installation Instructions Manual preview
08L07-TA1-203
Brand: Acura Pages: 6
Joie i-Level Instruction Manual preview
i-Level
Brand: Joie Pages: 53
POOL-LINE 110085 Assembly Instructions preview
110085
Brand: POOL-LINE Pages: 2
N-Com Bluetooth Kit3 PLUS User Instructions And Safety preview
Bluetooth Kit3 PLUS
Brand: N-Com Pages: 36
Billien OBU 5050 Quick Installation Manual preview
OBU 5050
Brand: Billien Pages: 2
Lexus ES 2021 Quick Manual preview
ES 2021
Brand: Lexus Pages: 28
Acura 08L03-TA1-200A Installation Instructions preview
08L03-TA1-200A
Brand: Acura Pages: 4

Brands by name

Popular brands

Load more brands