background image

The front passenger sensing system is designed to enable (may inflate)
the front passenger’s frontal airbag anytime the system senses that a
person of adult size is sitting properly in the front passenger seat.

When the front passenger sensing system enables the front passenger
frontal airbag (may inflate), the indicator will be unlit and stay unlit.

If a person of adult size is sitting in the front passenger’s seat, but the

passenger airbag off

or

pass airbag off

indicator lamp is lit, it is

possible that the person isn’t sitting properly in the seat. If this happens:

Turn the vehicle off and ask the person to place the seatback in the
full upright position.

Have the person sit upright in the seat, centered on the seat cushion,
with the person’s legs comfortably extended.

Restart the vehicle and have the person remain in this position for
about two minutes. This will allow the system to detect that person
and enable the passenger’s frontal airbag.

If the indicator lamp remains lit even after this, the person should be
advised to ride in the rear seat.

Occupant

Pass Airbag Off
Indicator Light

Passenger Airbag

Empty seat

Unlit

Disabled

Small child in child
safety seat or booster

Lit

Disabled

Small child with safety
belt buckled or
unbuckled

Lit

Disabled

Adult

Unlit

Enabled

Even with Advanced Restraints Systems, children 12 and under
should be properly restrained in the back seat.

After all occupants have adjusted their seats and put on safety belts, it’s
very important that they continue to sit properly. A properly seated
occupant sits upright, leaning against the seat back, and centered on the
seat cushion, with their feet comfortably extended on the floor. Sitting
improperly can increase the chance of injury in a crash event. For
example, if an occupant slouches, lies down, turns sideways, sits forward,
leans forward or sideways, or puts one or both feet up, the chance of
injury during a crash is greatly increased.

2008 Sable

(mgo)

Owners Guide (post-2002-fmt)
USA

(fus)

Seating and Safety Restraints

169

Summary of Contents for Sable 2008









































































































































































































































































































































Reviews: