Mercury Sable 2008 Owner'S Manual Download Page 119 | Manualshive

Page: 119 / 328

background image

REAR LEFT DOOR AJAR.

Displayed when the left rear door is not

completely closed.

REAR RIGHT DOOR AJAR.

Displayed when the right rear door is not

completely closed.

FUEL LEVEL LOW.

Displayed as an early reminder of a low fuel

condition.

CHECK CHARGING SYSTEM.

Displayed when the electrical system is

not maintaining proper voltage. If you are operating electrical accessories
when the engine is idling at a low speed, turn off as many of the
electrical loads as possible. If the warning stays on or comes on when the
engine is operating at normal speeds, have the electrical system checked
as soon as possible.

CHECK BRAKE SYSTEM.

Displayed when the brake system needs

servicing. If the warning stays on or continues to come on, contact your
authorized dealer as soon as possible.

LOW BRAKE FLUID.

Indicates the brake fluid level is low and the

brake system should be inspected immediately. Refer to

Brake fluid

reservoir

in the

Maintenance and Specifications

chapter.

PARK BRAKE ENGAGED.

Displayed when the park brake is engaged.

If the warning stays on after the park brake is off, contact your
authorized dealer as soon as possible.

LOW TIRE PRESSURE.

Displayed when one or more tires on your

vehicle have low tire pressure. Refer to

Inflating your tires

in the

Tires,

Wheels and Loading

chapter.

TIRE PRESSURE MONITOR FAULT.

Displayed when the Tire

Pressure Monitoring System is malfunctioning. If the warning stays on or
continues to come on, have the system inspected by your authorized
dealer.

TIRE PRESSURE SENSOR FAULT.

Displayed when a tire pressure

sensor is malfunctioning, or your spare tire is in use. For more
information on how the system operates under these conditions, refer to

Tire pressure monitoring system

in the

Tires, Wheels and Loading

chapter. If the warning stays on or continues to come on, have the
system inspected by your authorized dealer.

TRUNK AJAR.

Displayed when the trunk is not completely closed.

WASHER FLUID LEVEL LOW.

Indicates the washer fluid reservoir is

less than one quarter full. Check the washer fluid level. Refer to

Windshield washer fluid

in the

Maintenance and Specifications

chapter.

2008 Sable

(mgo)

Owners Guide (post-2002-fmt)
USA

(fus)

Driver Controls

119

«
...
117
118
119
120
121
...
»

Summary of Contents for Sable 2008









































































































































































































































































































































Reviews:

No comments

Related manuals for Sable 2008

Brand: DEFA Pages: 7

Brand: Prorack Pages: 15

Brand: Quadratec Pages: 8

Brand: Kia Pages: 51

Brand: Black Horse Off Road Pages: 7

Brand: ULTIMATE SPEED Pages: 10

Brand: TrailFX Pages: 2

Brand: Subaru Pages: 44

Brand: Jaeger Pages: 11

Brand: ATS Pages: 12

Brand: Ranger design Pages: 22

BLADE-AL-HK4-EN

Brand: iDataLink Pages: 35

Brand: Kia Pages: 46

Brand: Kuda Pages: 4

Brand: Or-Fab Pages: 5

Brand: Chevrolet Pages: 406

Brand: AA Products Pages: 6

Brand: Honda Pages: 682

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands