Mercury Sable 2008 Owner'S Manual Download Page 256

Page: 256 / 328

Stopping and securing the vehicle

1. Park on a level surface, set the
parking brake and activate hazard
flashers.

2. Place gearshift lever in P (Park)
and turn engine off.

Removing the spare tire and jack

1. Lift the trunk cargo cover, and
remove the wing nut that secures
the spare tire by turning it
counterclockwise.

2. Lift and remove the spare tire
from the trunk.

3. Remove the second wing nut that
secures the jack retention bracket
by turning it counterclockwise,
remove the jack kit from the
vehicle.

4. Remove the jack and the wrench
from the felt bag. Fold down the
wrench socket to use to loosen the
lug nuts and to operate the jack.

Tire change procedure

When one of the front wheels is off the ground, the transaxle
alone will not prevent the vehicle from moving or slipping off the

jack, even if the vehicle is in P (Park).

2008 Sable

(mgo)

Owners Guide (post-2002-fmt)
USA

(fus)

Roadside Emergencies

256

Summary of Contents for Sable 2008









































































































































































































































































































































Search results

Summary of Contents for Sable 2008

Reviews:

Related manuals for Sable 2008

Brands by name

Popular brands

Mercury Sable 2008, Owner'S Manual

Search results

Summary of Contents for Sable 2008

Reviews:

Related manuals for Sable 2008

Brands by name

Popular brands