Mercury Sable 2008 Owner'S Manual Download Page 59 | Manualshive

Page: 59 / 328

background image

Wired headphones

Do not leave children unattended in the vehicle and do not let
children operate the system while unsupervised. If wired

headphones or auxiliary systems are used, children may become
entangled in the cords and seriously injure themselves.

The driver should never use the headphones while driving the
vehicle. Using headphones may prevent the driver from hearing

audible warnings such as horns or emergency sirens, which could
result in a crash causing serious injury. Give your full attention to
driving and to the road.

You may purchase wired headphones for your FES (Family
Entertainment System). Plug them into the 3.5 mm headphone jack(s)
located on the left and right sides of the system. (Channel A is located
on the left side and Channel B is located on the right side.) These
headphones will be active when in Dual Play mode.

To listen to the audio on wired headphones (not included), connect the
wired headphones into the headphone jacks on the sides of the DVD
system. The wired headphone jack for Channel A is located on the left
side of the FES and is labeled

A. Headphones plugged into this

headphone jack will hear audio from the audio source selected to be the
Channel A source. The wired headphone jack for Channel B is located on
the right side of the FES and is labeled

B. Headphones plugged into

this headphone jack will hear audio from the audio source selected to be
the Channel B source.

Adjust the headphone volume using
the volume control on the DVD
system.

Operation

Single play/Dual play

Your DVD and audio system work together with the infrared headphones
and wired headphones (not included) to allow the rear seat passengers
to listen to the radio (and other media sources) over the headphones.
This enables the front and rear seat passengers to listen to a variety of
sources a variety of ways.

2008 Sable

(mgo)

Owners Guide (post-2002-fmt)
USA

(fus)

Entertainment Systems

59

«
...
57
58
59
60
61
...
»

Summary of Contents for Sable 2008









































































































































































































































































































































Reviews:

No comments

Related manuals for Sable 2008

Brand: iArmor Pages: 6

Brand: Victory 4x4 Pages: 13

Brand: Haibang Pages: 6

BLADE-AL(TB)-TL2

Brand: iDataLink Pages: 9

Brand: Magneti Marelli Pages: 2

Brand: Dometic Pages: 158

Brand: Quadratec Pages: 6

Brand: ULTIMATE SPEED Pages: 40

Brand: cam Pages: 6

Brand: Demco Pages: 4

Magic Watch MWE-850-4DSM

Brand: Waeco Pages: 204

Brand: Anker Technology Pages: 8

Brand: Thule Pages: 2

Brand: Honda Pages: 330

Brand: CITROEN Pages: 86

Brand: Rosco Pages: 12

Brand: AUTOTECH Pages: 2

Brand: Opel Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands