manualshive.com logo in svg

Mercury Sable 2008, Owner'S Manual

The Mercury Sable 2008 Quick Reference Manual is a comprehensive guide to help you make the most of your vehicle. This user-friendly manual provides detailed instructions and essential information about your car's features and maintenance. Download it for free at manualshive.com and enjoy hassle-free driving with your Mercury Sable 2008.

Share
Download
background image

•

A headliner designed to flex open above the side doors to allow Safety
Canopy™ deployment.

•

The same readiness airbag light, electronic control and diagnostic unit
as used for the front airbags.

•

Two crash sensors mounted on the B pillar (one on each side of the
vehicle).

•

Two crash sensors located at the C pillar behind the rear doors (one
on each side of the vehicle).

•

Rollover sensor in the restraints control module (RCM).

The Safety Canopy™ system, in combination with safety belts, can help
reduce the risk of severe injuries in the event of a significant side impact
collision or rollover event.

Children 12 years old and under should always be properly restrained in
the second row seats. The Safety Canopy™ will not interfere with
children restrained using a properly installed child or booster seat
because it is designed to inflate downward from the headliner above the
doors along the side window opening.

The Safety Canopy™ system is designed to activate when the vehicle
sustains lateral deceleration sufficient to cause the side crash sensor to
close an electrical circuit that initiates Safety Canopy™ inflation or when
a certain likelihood of a rollover event is detected by the rollover sensor.

The Safety Canopy™ is mounted to roof side-rail sheet metal, behind the
headliner, along the entire side of the vehicle. In certain lateral collisions
or rollover events, the Safety Canopy™ system will be activated,
regardless of which seats are occupied. The Safety Canopy™ is designed
to inflate between the side window area and occupants to further
enhance protection provided in side impact collisions and rollover events.

The fact that the Safety Canopy™ did not activate in a collision does not
mean that something is wrong with the system. Rather, it means the
forces were not of the type sufficient to cause activation. The Safety
Canopy™ is designed to inflate in certain side impact collisions or
rollover events, not in rear impact, frontal or near-frontal collisions,
unless the collision causes sufficient lateral deceleration or rollover
likelihood.

Several Safety Canopy™ system components get hot after
inflation. Do not touch them after inflation.

2008 Sable

(mgo)

Owners Guide (post-2002-fmt)
USA

(fus)

Seating and Safety Restraints

176

Summary of Contents for Sable 2008









































































































































































































































































































































Reviews:

No comments

Related manuals for Sable 2008

LAMBORGHINI URUS Quick Manual preview
URUS
Brand: LAMBORGHINI Pages: 48
Waeco MagicWatch MWE800 Installation And Operating Manual preview
MagicWatch MWE800
Brand: Waeco Pages: 212
Whispbar K783W Fitting Instructions Manual preview
K783W
Brand: Whispbar Pages: 16
iDataLink maestro Pr 2 Install Manual preview
maestro Pr 2
Brand: iDataLink Pages: 99
Spiral Audio KT-FI001PB Nstallation Instructions preview
KT-FI001PB
Brand: Spiral Audio Pages: 2
Maserati Quattroporte Automatic Owner'S Manual preview
Quattroporte Automatic
Brand: Maserati Pages: 272
Harman Kardon DP 2US Quick Start Manual preview
DP 2US
Brand: Harman Kardon Pages: 16
TATA Motors TIAGO XZ 2019 Owner'S Manual preview
TIAGO XZ 2019
Brand: TATA Motors Pages: 184
B&G electronics PW-50C Civilian Installation And Operation Manual preview
PW-50C Civilian
Brand: B&G electronics Pages: 7
ULTIMATE SPEED 304669 Instructions For Use And Safety Manuallines preview
304669
Brand: ULTIMATE SPEED Pages: 50
Jaeger 12020523 Fitting Instructions Manual preview
12020523
Brand: Jaeger Pages: 11
Ford ALCON 1968 Owner'S Manual preview
ALCON 1968
Brand: Ford Pages: 52
KlipXtreme Ridesmart KMA-610 Manual preview
Ridesmart KMA-610
Brand: KlipXtreme Pages: 12
Advent MAZBTSW2 Owner'S Manual preview
MAZBTSW2
Brand: Advent Pages: 8
BMW X1 2015 Owner'S Manual preview
X1 2015
Brand: BMW Pages: 242
Kleinn Air Horns GMTRK-3 Install Manual preview
GMTRK-3
Brand: Kleinn Air Horns Pages: 38
Curt Group Retrac 207700 Installation Manual preview
Retrac 207700
Brand: Curt Group Pages: 4
Honda 2011 FIT Owner'S Manual preview
2011 FIT
Brand: Honda Pages: 358

Brands by name

Popular brands

Load more brands