Mercury Sable 2008 Owner'S Manual Download Page 79 | Manualshive

Page: 79 / 328

background image

8.

Airflow direction control:

Press to toggle through the air distribution

modes listed below. The selected mode will be shown in the display.

:

Distributes air through the instrument panel and center console

vents (if equipped).

:

Distributes air through the instrument panel, floor and center

console vents (if equipped).

:

Distributes air through the floor vents.

Note:

You may notice a

small amount of air flowing from the demister and defroster vents.

:

Distributes air through the windshield defroster, demister and floor

vents.

9.

Manual override controls:

Allows you to manually select where

airflow is directed. To return to full automatic control, press AUTO.

10.

Driver heated seat control:

Press to heat the driver seat. Press

once to activate high heat (two indicator lights). Press again to activate
low heat (one indicator light). Press again to deactivate the driver
heated seat.

11.

Front fan speed control:

Press to manually increase or

decrease the fan speed. To return to automatic fan operation, press
AUTO.

12.

EXT:

Press to display outside temperature. Press again to display

cabin temperature settings.

13.

°F/°C (Temperature conversions):

Press to switch temperature

display between Fahrenheit and Celsius.

14.

OFF:

Outside air is shut out and the climate control system is turned

off.

15.

Driver temperature control:

Press to increase/decrease the

temperature on the driver side of the cabin. Sets the passenger side
temperature also when DUAL is disengaged. The recommended vehicle
cabin setting is between 72°F (22°C) and 75°F (24°C).

16.

AUTO:

Press to engage automatic temperature control. Select the

desired temperature using the temperature control. The system will
automatically determine fan speed, airflow location, A/C on or off, and
outside or recirculated air, to heat or cool the vehicle to reach the
desired temperature.

2008 Sable

(mgo)

Owners Guide (post-2002-fmt)
USA

(fus)

Climate Controls

79

«
...
77
78
79
80
81
...
»

Summary of Contents for Sable 2008









































































































































































































































































































































Reviews:

No comments

Related manuals for Sable 2008

PRIME DESIGN VCR 326

Brand: Safe Fleet Pages: 16

Prime Design VBC PC11

Brand: Safe Fleet Pages: 8

Prime Design AR1418

Brand: Safe Fleet Pages: 4

Multiple G9F18 AU000

Brand: Genesis Pages: 3

10-8002-C11998B

Brand: Saleen Pages: 12

2013 Buick Verano

Brand: Buick Pages: 5

Intercooler Kit Type 31

Brand: GReddy Pages: 9

CB-796IG2-CIGD-R

Brand: CARRYBOY Pages: 4

Brand: GMC Pages: 428

DLD Wide Range II

Brand: VDO Pages: 84

TravelCharge Companion GO-Plus

Brand: Wagan Pages: 3

Parrot MKi + ParrotCK3100 range LOGAN

Brand: Parrot Pages: 10

Brand: Saab Pages: 92

Brand: A-rival Pages: 23

Alloy Rugged Ridge X-Clamp

Brand: Omix-Ada Pages: 2

Brand: Dodge Pages: 3

Brand: S3 Power Sports Pages: 2

2004 Impreza OUTBACK SPORT

Brand: Subaru Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands