Mercury Sable 2008 Owner'S Manual Download Page 24

Page: 24 / 328

SPEED VOL (Speed sensitive volume, if equipped):

Press MENU to

reach the SPEEDVOL setting. Radio volume automatically gets louder
with increasing vehicle speed to compensate for road and wind noise.
Use

to adjust.

The default setting is

off;

increasing your vehicle speed will not change

the volume level.

Adjust

1–7:

Increasing this setting from 1 (lowest setting) to 7 (highest

setting) allows the radio volume to automatically change slightly with
vehicle speed to compensate for road and wind noise.

Recommended level is

1–3;

SPEED OFF turns the feature off and level 7

is the maximum setting.

TRACK/FOLDER MODE:

Available only on MP3 discs in CD mode.

In track mode, press

SEEK, SEEK

to scroll through all tracks on

the disc
In folder mode, press

SEEK, SEEK

to scroll through tracks

within the selected folder.
Press

FOLDER, FOLDER

to access the previous/next folder (if

available). Press OK to close and return to the main menu.

COMPRESS (Compression):

Available only in CD/MP3 mode. Press

MENU until COMPRESS ON/OFF appears in the display. Use

toggle ON/OFF. When COMPRESS is ON, the system will bring the soft
and loud CD passages together for a more consistent listening level.

SINGLE PLAY/DUAL PLAY (if equipped):

If SINGLE PLAY is ON,

press

for DUAL PLAY. For further information on Single

Play/Dual Play, please refer to the

Family Entertainment DVD system

later in this section.

AUX:

Press repeatedly to cycle

through FES/DVD (if equipped),
LINE IN (auxiliary audio mode),
SAT1, SAT2 and SAT3 (satellite radio, if equipped) and SYNC (if
equipped).
For location and further information on auxiliary audio mode, refer to

Auxiliary input jack

later in this chapter.

Satellite radio is available only with a valid SIRIUS radio
subscription. Check with your authorized dealer for availability.

If your vehicle is equipped with a Family Entertainment System (FES)
please refer to the

Family Entertainment DVD system

later in this

chapter.

2008 Sable

(mgo)

Owners Guide (post-2002-fmt)
USA

(fus)

Entertainment Systems

Summary of Contents for Sable 2008









































































































































































































































































































































Search results

Summary of Contents for Sable 2008

Reviews:

Related manuals for Sable 2008

Brands by name

Popular brands

Mercury Sable 2008, Owner'S Manual

Search results

Summary of Contents for Sable 2008

Reviews:

Related manuals for Sable 2008

Brands by name

Popular brands