manualshive.com logo in svg

Mercury Sable 2008, Owner'S Manual

The Mercury Sable 2008 Quick Reference Manual is a comprehensive guide to help you make the most of your vehicle. This user-friendly manual provides detailed instructions and essential information about your car's features and maintenance. Download it for free at manualshive.com and enjoy hassle-free driving with your Mercury Sable 2008.

Share
Download
background image

4. Press the SETUP control
repeatedly until the message center
says “RESET FOR ZONE SETTING”.

5. Press the RESET control to enter
Zone Setting mode.

6. Press RESET repeatedly until the
desired zone setting is displayed.
The message center will
automatically exit zone setting mode
if enough time passes without
pressing a button.

Compass calibration adjustment

Perform the following steps on an open area free from steel structures
and high voltage lines. For optimum calibration, turn off all electrical
accessories (heater / air conditioning, wipers, etc.) and make sure all
vehicle doors are shut.

1. Turn ignition to the ON position.

2. Start the engine.

3. Press the SETUP button
repeatedly until the message center
displays “RESET FOR
CALIBRATION”.

4. Press RESET to enter compass
calibration mode which will display
“CIRCLE SLOWLY TO CALIBRATE”.

5. Drive the vehicle in circles up to
three times until the message

⬙

CALIBRATION COMPLETED

⬙

appears and one of the 8 valid
headings (N, NE, E, SE, S, SW, W,
NW) is displayed.

6. Verify that the calibration process has taken place by driving the
vehicle in at least one circle, confirming that the heading changes
accordingly. If this happens, the compass has been calibrated
successfully. Otherwise, if the display shows only one heading as the
vehicle is being driven around, repeat the procedure from Step 3.

2008 Sable

(mgo)

Owners Guide (post-2002-fmt)
USA

(fus)

Driver Controls

114

Summary of Contents for Sable 2008









































































































































































































































































































































Reviews:

No comments

Related manuals for Sable 2008

Jabra FREEWAY Datasheet preview
FREEWAY
Brand: Jabra Pages: 2
Jabra BT330 User Manual preview
BT330
Brand: Jabra Pages: 38
OEM Audio Reference Series Manual preview
Reference Series
Brand: OEM Audio Pages: 29
Carefree Slideout Cover Service Manual preview
Slideout Cover
Brand: Carefree Pages: 12
Paxton Automotive Novi Owner'S Installation Manual preview
Novi
Brand: Paxton Automotive Pages: 85
Thule 1489 Instructions Manual preview
1489
Brand: Thule Pages: 8
PullRite 20K OE Series Installation Instructions Manual preview
20K OE Series
Brand: PullRite Pages: 10
BESAFE iZi Flex Manual preview
iZi Flex
Brand: BESAFE Pages: 4
Lit Lightz RGBW Rock Lights Setup Manual preview
RGBW Rock Lights
Brand: Lit Lightz Pages: 3
Mercedes-Benz 2015 SLK Operator'S Manual preview
2015 SLK
Brand: Mercedes-Benz Pages: 358
GMC TopKick 2007 Owner'S Manual preview
TopKick 2007
Brand: GMC Pages: 430
Havis-Shields 1996-2008 Crown Victoria Driver and Passenger - Trunk Side Mounts C-TSM-CV-P Datasheet preview
1996-2008 Crown Victoria Driver and Passenger - Trunk Side Mounts C-TSM-CV-P
Brand: Havis-Shields Pages: 1
Thule 1809 Instruction Manual preview
1809
Brand: Thule Pages: 4
Columbia THERAPEDIC 2000 Instructions For Use Manual preview
THERAPEDIC 2000
Brand: Columbia Pages: 14
Volvo S90 - ACCESSORY PANEL Owner'S Manual Supplement preview
S90 - ACCESSORY PANEL
Brand: Volvo Pages: 166
CARFACE CF145962E Instruction Manual preview
CF145962E
Brand: CARFACE Pages: 16
KAP HK CARPLAY 10w Instruction Manual preview
HK CARPLAY 10w
Brand: KAP Pages: 22
Honda 2002 Accord Coupe Owner'S Manual preview
2002 Accord Coupe
Brand: Honda Pages: 367

Brands by name

Popular brands

Load more brands