manualshive.com logo in svg

Mercury Sable 2008, Owner'S Manual

The Mercury Sable 2008 Quick Reference Manual is a comprehensive guide to help you make the most of your vehicle. This user-friendly manual provides detailed instructions and essential information about your car's features and maintenance. Download it for free at manualshive.com and enjoy hassle-free driving with your Mercury Sable 2008.

Share
Download
background image

Position the safety belt height adjusters so that the belt rests
across the middle of your shoulder. Failure to adjust the safety

belt properly could reduce the effectiveness of the seat belt and
increase the risk of injury in a collision.

Safety belt pretensioner

Your vehicle is equipped with safety belt pretensioners at the driver and
front outboard passenger seating positions.

The safety belt pretensioner tightens the safety belts firmly against the
occupant’s body at the start of the crash.

The driver and front passenger safety belt system (including
retractors, buckles and height adjusters) must be replaced if the

vehicle is involved in a collision that results in deployment of front
airbags, seat-mounted side airbags and Safety Canopy™, and safety
belt pretensioners.

Safety belt extension assembly

If the safety belt is too short when fully extended, there is a 8 inch
(20 cm) safety belt extension assembly that can be added (part number
611C22). This assembly can be obtained from an authorized dealer.

Use only extensions manufactured by the same supplier as the safety
belt. Manufacturer identification is located at the end of the webbing on
the label. Also, use the safety belt extension only if the safety belt is too
short for you when fully extended.

Do not use extensions to change the fit of the shoulder belt
across the torso.

Safety belt maintenance

Inspect the safety belt systems periodically to make sure they work
properly and are not damaged. Inspect the safety belts to make sure
there are no nicks, tears or cuts. Replace if necessary. All safety belt
assemblies, including retractors, buckles, front safety belt buckle
assemblies, buckle support assemblies (slide bar-if equipped), shoulder
belt height adjusters (if equipped), shoulder belt guide on seatback (if
equipped), child safety seat LATCH and tether anchors, and attaching

2008 Sable

(mgo)

Owners Guide (post-2002-fmt)
USA

(fus)

Seating and Safety Restraints

158

Summary of Contents for Sable 2008









































































































































































































































































































































Reviews:

No comments

Related manuals for Sable 2008

Toyota 2011 Corolla LE Brochure preview
2011 Corolla LE
Brand: Toyota Pages: 19
Ford 2008 Mustang Quick Reference Manual preview
2008 Mustang
Brand: Ford Pages: 2
Metra Electronics 99-3103 Installation Instructions preview
99-3103
Brand: Metra Electronics Pages: 2
BESAFE iZi Flex Manual preview
iZi Flex
Brand: BESAFE Pages: 4
Toyota 4Runner 2019 Quick Reference Manual preview
4Runner 2019
Brand: Toyota Pages: 52
FALCON RIDGE BC-3400-FC05 Instructions For Installation And Care preview
BC-3400-FC05
Brand: FALCON RIDGE Pages: 7
Volvo 2004 C70 HPT User Manual preview
2004 C70 HPT
Brand: Volvo Pages: 30
Mercedes-Benz Sprinter 2003 Manual preview
Sprinter 2003
Brand: Mercedes-Benz Pages: 296
GReddy 12519101 Instruction Manual preview
12519101
Brand: GReddy Pages: 12
Fabbri BICI OK 2 Manual preview
BICI OK 2
Brand: Fabbri Pages: 32
Whelen Engineering Company SAK34 Installation Manual preview
SAK34
Brand: Whelen Engineering Company Pages: 2
Gator ARV43M Instruction Manual preview
ARV43M
Brand: Gator Pages: 5
Waeco MagicWatch MWE150 Installation And Operating Manual preview
MagicWatch MWE150
Brand: Waeco Pages: 176
Ford 2003 Ranger Quick Reference Manual preview
2003 Ranger
Brand: Ford Pages: 2
Toyota 4Runner 2020 Owner'S Manual preview
4Runner 2020
Brand: Toyota Pages: 596
BMW 84 64 0 025 810 Installation Instructions Manual preview
84 64 0 025 810
Brand: BMW Pages: 25
Toyota YARIS SEDAN 2019 Quick Reference Manual preview
YARIS SEDAN 2019
Brand: Toyota Pages: 17
Volkswagen RCD550 Installation Manual preview
RCD550
Brand: Volkswagen Pages: 4

Brands by name

Popular brands

Load more brands