Mercury Sable 2008 Owner'S Manual Download Page 220

Page: 220 / 328

Note:

If you tow your vehicle with all four wheels on the ground, follow

these instructions:

•

Tow only in the forward direction

•

Release the parking brake

•

Place the transmission shift lever in Neutral (N)

•

Turn the key in the ignition to the ACC position (refer to

Starting

the

Driving

chapter). The ACC position also unlocks the steering

wheel.

•

Do not exceed 65 mph (105 km/h)

•

Start the engine and allow it to run for five minutes at the beginning
of each day and at each fuel stop.

2008 Sable

(mgo)

Owners Guide (post-2002-fmt)
USA

(fus)

Tires, Wheels and Loading

220

Summary of Contents for Sable 2008









































































































































































































































































































































Search results

Summary of Contents for Sable 2008

Reviews:

Related manuals for Sable 2008

Brands by name

Popular brands

Mercury Sable 2008, Owner'S Manual

Search results

Summary of Contents for Sable 2008

Reviews:

Related manuals for Sable 2008

Brands by name

Popular brands