Mercury Sable 2008 Owner'S Manual Download Page 89

Page: 89 / 328

Replacing front parking lamp/turn signal bulbs

1. Make sure headlamp switch is in the OFF position, then open the
hood.

2. Reach in behind the headlamp assembly to access the bulb sockets
and connectors.

3. Locate the electrical connector
and remove it by releasing the
locking tab and pulling it straight
down.

4. Remove the bulb socket by
turning it counterclockwise and
pulling it straight out.

5. To remove the bulb, pull it
straight out of the bulb socket.

Install the new bulb(s) in reverse order.

Replacing front sidemarker bulb

1. Make sure the headlamp control
is in the OFF position.

2. Reach under the side of the front
fascia to access the bulb sockets
and connectors.

3. Remove the bulb socket by
rotating it counterclockwise, then
pulling it out of the lamp assembly.

4. Pull the bulb straight from the
socket.

Install new bulb in reverse order.

Replacing rear stop/tail/turn signal/backup lamp bulbs

The stop/tail/turn signal/backup lamp bulbs are located in the tail lamp
assembly. Follow the same steps to replace either bulb.

Note:

Your vehicle is equipped with a stop/tail lamp assembly containing

integral multiple light emitting diodes (LED). If replacement is required,
see your authorized dealer.

2008 Sable

(mgo)

Owners Guide (post-2002-fmt)
USA

(fus)

Lights

Summary of Contents for Sable 2008









































































































































































































































































































































Search results

Summary of Contents for Sable 2008

Reviews:

Related manuals for Sable 2008

Brands by name

Popular brands

Mercury Sable 2008, Owner'S Manual

Search results

Summary of Contents for Sable 2008

Reviews:

Related manuals for Sable 2008

Brands by name

Popular brands