Mercury Sable 2008 Owner'S Manual Download Page 102

Page: 102 / 328

3. Press the SET + control and
release it.

4. Take your foot off the accelerator
pedal.

5. The indicator

light on the

instrument cluster will turn on.

Note:

•

Vehicle speed may vary momentarily when driving up and down a
steep hill.

•

If the vehicle speed increases above the set speed on a downhill, you
may want to apply the brakes to reduce the speed.

•

If the vehicle speed decreases more than 10 mph (16 km/h) below
your set speed on an uphill, your speed control will disengage.

Disengaging speed control

To disengage the speed control:

•

Depress the brake pedal or press CNCL (Cancel).

Disengaging the speed control will not erase previous set speed.

Resuming a set speed

Press the RES control and release
it. This will automatically return the
vehicle to the previously set speed.

SET

RSM

CNCL

OFF

SET

RSM

CNCL

OFF

2008 Sable

(mgo)

Owners Guide (post-2002-fmt)
USA

(fus)

Driver Controls

102

Summary of Contents for Sable 2008









































































































































































































































































































































Search results

Summary of Contents for Sable 2008

Reviews:

Related manuals for Sable 2008

Brands by name

Popular brands

Mercury Sable 2008, Owner'S Manual

Search results

Summary of Contents for Sable 2008

Reviews:

Related manuals for Sable 2008

Brands by name

Popular brands