Mercury Sable 2008 Owner'S Manual Download Page 14

Page: 14 / 328

GAUGES

Speedometer:

Indicates the

current vehicle speed.

Engine coolant temperature
gauge:

Indicates engine coolant

temperature. At normal operating
temperature, the needle will be in
the normal range (between “H” and
“C”).

If it enters the red section,

the engine is overheating. Stop
the vehicle as soon as safely
possible, switch off the engine and let the engine cool.

Never remove the coolant reservoir cap while the engine is
running or hot.

2008 Sable

(mgo)

Owners Guide (post-2002-fmt)
USA

(fus)

Instrument Cluster

Summary of Contents for Sable 2008









































































































































































































































































































































Search results

Summary of Contents for Sable 2008

Reviews:

Related manuals for Sable 2008

Brands by name

Popular brands

Mercury Sable 2008, Owner'S Manual

Search results

Summary of Contents for Sable 2008

Reviews:

Related manuals for Sable 2008

Brands by name

Popular brands