Mercury Sable 2008 Owner'S Manual Download Page 153 | Manualshive

Page: 153 / 328

background image

allows your Personal Safety System™ to tailor the airbag deployment
and safety belt pretensioner activation depending upon safety belt usage.
Refer to

Safety belt

section in this chapter.

Front safety belt pretensioners

The safety belt pretensioners at the front outboard seating positions are
designed to tighten the safety belts firmly against the occupant’s body
during frontal collisions, and in side collisions and rollovers. This helps
increase the effectiveness of the safety belts. In frontal collisions, the
safety belt pretensioners can be activated alone or, if the collision is of
sufficient severity, together with the front airbags.

Front safety belt energy management retractors

The front outboard safety belt energy management retractors allow
webbing to be pulled out of the retractor in a gradual and controlled
manner in response to the occupant’s forward momentum. This helps
reduce the risk of force-related injuries to the occupant’s chest by
limiting the load on the occupant. Refer to

Energy management feature

section in this chapter.

Determining if the Personal Safety System™ is operational

The Personal Safety System™ uses a warning light in the instrument
cluster or a back-up tone to indicate the condition of the system. Refer
to the

Warning lights and chimes

section in the

Instrument Cluster

chapter. Routine maintenance of the Personal Safety System™ is not
required.

The Restraints Control Module (RCM) monitors its own internal circuits
and the circuits for the airbag supplemental restraints, crash sensor(s),
safety belt pretensioners, front safety belt buckle sensors, driver seat
position sensor, and front passenger sensing system. In addition, the
RCM also monitors the restraints warning light in the instrument cluster.
A difficulty with the system is indicated by one or more of the following.

•

The warning light will either flash or stay lit.

•

The warning light will not illuminate immediately after ignition is
turned on.

•

A series of five beeps will be heard. The tone pattern will repeat
periodically until the problem and warning light are repaired.

If any of these things happen, even intermittently, have the Personal
Safety System™ serviced at an authorized dealer immediately. Unless
serviced, the system may not function properly in the event of a
collision.

2008 Sable

(mgo)

Owners Guide (post-2002-fmt)
USA

(fus)

Seating and Safety Restraints

153

«
...
151
152
153
154
155
...
»

Summary of Contents for Sable 2008









































































































































































































































































































































Reviews:

No comments

Related manuals for Sable 2008

Brand: A-Tach Mounts Pages: 2

Brand: Metra Electronics Pages: 12

Brand: Halfords Pages: 4

Brand: MASCOT Pages: 12

Brand: BURY Pages: 2

RGBW Rock Lights

Brand: Lit Lightz Pages: 3

Brand: Power Acoustik Pages: 4

Brand: Linear Logic Pages: 8

Brand: BMW Pages: 392

Brand: Curt Manufacturing Pages: 4

Brand: PUTCO Pages: 3

Charger SRT 392 2017

Brand: Dodge Pages: 576

Brand: Lexus Pages: 108

Brand: STO N SHO Pages: 7

Auto Security AA-9103N

Brand: Audiovox Pages: 1

MagicComfort MSH50

Brand: Waeco Pages: 104

Brand: Mercedes-Benz Pages: 108

Brand: Fass Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands