Mercury Sable 2008 Owner'S Manual Download Page 229

Page: 229 / 328

•

Entering a paved road from a gravel road, or vice versa

•

Hitting a curb while turning

•

Cornering at excessive speeds while towing a heavily loaded trailer
(refer to

Trailer towing

in the

Tires, Wheels and Loading

chapter)

The AdvanceTrac

威

system automatically turns on when the engine is

started. However, the system does not function when the vehicle is
traveling in R (Reverse).

If you are operating the speed control system and road conditions
change causing the AdvanceTrac

威

to activate, the AdvanceTrac

威

will

disengage the speed control. When driving conditions permit, you can
return to speed control by pressing the RES control. Refer to

Speed

control

in the

Driver controls

chapter.

The AdvanceTrac

威

button allows the

driver to control the availability of
the AdvanceTrac

威

system.

AdvanceTrac

威

system status is

indicated by the AdvanceTrac

威

indicator light in the instrument
cluster when the system is deactivated.

The AdvanceTrac

威

system cannot be deactivated when the vehicle speed

is above 45 mph (70 km/h) even though the AdvanceTrac

威

indicator light

may be illuminated in the instrument cluster.

If a failure is detected in the AdvanceTrac

威

system, the AdvanceTrac

威

indicator light in the instrument cluster will stay on. Have the vehicle
system serviced by an authorized dealer immediately.

If the vehicle is stuck in snow or mud or when driving in deep sand,
switching off the AdvanceTrac

威

system may be beneficial so the wheels

are allowed to spin. If your vehicle seems to lose engine power while
driving in deep sand or very deep snow, switching off the AdvanceTrac

威

stability enhancement feature will restore full engine power and will
enhance momentum through the obstacle.

Some drivers may notice a slight movement of the brake pedal when the
AdvanceTrac

威

performs a system self-check. During AdvanceTrac

威

operation you may experience the following:

•

A rumble or grinding noise

•

A slight deceleration of the vehicle

•

The AdvanceTrac

威

indicator light will illuminate

•

If your foot is on the brake pedal, you will feel a vibration in the
pedal.

2008 Sable

(mgo)

Owners Guide (post-2002-fmt)
USA

(fus)

Driving

229

Summary of Contents for Sable 2008









































































































































































































































































































































Search results

Summary of Contents for Sable 2008

Reviews:

Related manuals for Sable 2008

Brands by name

Popular brands

Mercury Sable 2008, Owner'S Manual

Search results

Summary of Contents for Sable 2008

Reviews:

Related manuals for Sable 2008

Brands by name

Popular brands