Mercury Sable 2008 Owner'S Manual Download Page 129 | Manualshive

Page: 129 / 328

background image

On hot days, the temperature in the trunk or vehicle interior can
rise very quickly. Exposure of people or animals to these high

temperatures for even a short time can cause death or serious
heat-related injuries, including brain damage. Small children are
particularly at risk.

REMOTE ENTRY SYSTEM

The Integrated Keyhead Transmitter (IKT) complies with part 15 of the
FCC rules and with RSS-210 of Industry Canada. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.

The typical operating range for your IKT is approximately 33 feet
(10 meters). A decrease in operating range could be caused by:

•

weather conditions,

•

nearby radio towers,

•

structures around the vehicle, or

•

other vehicles parked next to your vehicle.

The IKT allows you to:

•

remotely unlock the vehicle
doors.

•

remotely lock all the vehicle
doors.

•

remotely open the trunk.

•

activate the personal alarm.

•

operate the illuminated entry
feature.

•

arm and disarm the perimeter
anti-theft system (if equipped)

The remote entry lock/unlock feature operates in any ignition position
except while the key is held in the 4 (START) position. The panic
feature operates with the key in the 1 (LOCK) position.

2008 Sable

(mgo)

Owners Guide (post-2002-fmt)
USA

(fus)

Locks and Security

129

«
...
127
128
129
130
131
...
»

Summary of Contents for Sable 2008









































































































































































































































































































































Reviews:

No comments

Related manuals for Sable 2008

Brand: Hama Pages: 2

Brand: Abarth Pages: 36

Brand: RaceChip Pages: 12

ANDROID INTERFACE

Brand: GMC Pages: 18

Brand: Prorack Pages: 15

Brand: Kuda Pages: 3

Brand: Kuda Pages: 2

Brand: Warn Pages: 5

Brand: Rugged Ridge Pages: 5

Brand: Kleinn Pages: 8

Brand: Ranger design Pages: 22

Brand: Maserati Pages: 37

1995 Roadmaster

Brand: Buick Pages: 340

Brand: Edelbrock Pages: 2

Brand: 3UVIEW Pages: 15

Brand: TEINHOF Pages: 2

Brand: Davis Instruments Pages: 16

Brand: PIE Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands