manualshive.com logo in svg

Mercury Sable 2008, Owner'S Manual

The Mercury Sable 2008 Quick Reference Manual is a comprehensive guide to help you make the most of your vehicle. This user-friendly manual provides detailed instructions and essential information about your car's features and maintenance. Download it for free at manualshive.com and enjoy hassle-free driving with your Mercury Sable 2008.

Share
Download
background image

3. Locate the correct anchor for the
selected seating position.

4. Open the tether anchor cover.

5. Clip the tether strap to the
anchor as shown.

If the tether strap is clipped
incorrectly, the child safety

seat may not be retained properly
in the event of a collision.

6. Install the child safety seat tightly using the LATCH anchors or safety
belts. Follow the instructions in this chapter.

7. Tighten the child safety seat tether strap according to the
manufacturer’s instructions.

If the safety seat is not anchored properly, the risk of a child
being injured in a collision greatly increases.

2008 Sable

(mgo)

Owners Guide (post-2002-fmt)
USA

(fus)

Seating and Safety Restraints

187

Summary of Contents for Sable 2008









































































































































































































































































































































Reviews:

No comments

Related manuals for Sable 2008

AA Products KX405 Instruction Manual preview
KX405
Brand: AA Products Pages: 8
Parrot CK3300 Setup Information Manual preview
CK3300
Brand: Parrot Pages: 19
Parrot Minikit+ Quick Start Manual preview
Minikit+
Brand: Parrot Pages: 88
Parrot Minikit+ Information Sheet preview
Minikit+
Brand: Parrot Pages: 2
Parrot CK3100 LCD Specifications preview
CK3100 LCD
Brand: Parrot Pages: 2
Parrot CK 3000 Evolution Installation Notes preview
CK 3000 Evolution
Brand: Parrot Pages: 8
Parrot CK 3000 Evolution User Manual preview
CK 3000 Evolution
Brand: Parrot Pages: 106
Carax HUD CRX-3001 Quick Start Manual preview
HUD CRX-3001
Brand: Carax Pages: 2
Cadillac 1999 DeVille Owner'S Manual preview
1999 DeVille
Brand: Cadillac Pages: 368
Luverne 205760 Installation Instructions preview
205760
Brand: Luverne Pages: 3
Navman B2+ User Manual preview
B2+
Brand: Navman Pages: 27
P-Invent Troller User Manual preview
Troller
Brand: P-Invent Pages: 4
Safe Fleet PRIME DESIGN URX-001-E Manual preview
PRIME DESIGN URX-001-E
Brand: Safe Fleet Pages: 8
Skoda Superb 2006 Owner'S Manual preview
Superb 2006
Brand: Skoda Pages: 281
BraunAbility Rampvan Maintenance And Service Manual preview
Rampvan
Brand: BraunAbility Pages: 46
Westfalia 859528 Original Instructions Manual preview
859528
Brand: Westfalia Pages: 10
KLAUS Multiparking trendvario6X00 Service Manual preview
trendvario6X00
Brand: KLAUS Multiparking Pages: 72
Xpresskit PKTX Installation Manual preview
PKTX
Brand: Xpresskit Pages: 12

Brands by name

Popular brands

Load more brands