Mercury Sable 2008 Owner'S Manual Download Page 108 | Manualshive

Page: 108 / 328

background image

U.S. federal safety standards (this includes any garage door opener
model manufactured before April 1, 1982). A garage door which cannot
detect an object, signaling the door to stop and reverse, does not meet
current U.S. federal safety standards. For more information, contact
HomeLink

威

at:

www.homelink.com

or

1–800–355–3515.

Retain the original transmitter for use in other vehicles as well as for
future programming procedures (i.e. new HomeLink

威

equipped vehicle

purchase). It is also suggested that upon the sale of the vehicle, the
programmed Homelink

威

buttons be erased for security purposes, refer to

Programming

in this section.

Programming

Do not program HomeLink

威

with the vehicle parked in the garage.

Note:

Your vehicle may require the ignition switch to be turned to the

ACC position for programming and/or operation of the HomeLink

威

. It is

also recommended that a new battery be placed in the hand-held
transmitter of the device being programmed to HomeLink

威

for quicker

training and accurate transmission of the radio-frequency signal.

1. Position the end of your
hand-held transmitter 1–3 inches
(2–8 cm) away from the HomeLink

威

button you wish to program (located
on your visor) while keeping the
indicator light in view.

2. Simultaneously press and hold
both the chosen HomeLink

威

and

hand-held transmitter buttons until the HomeLink

威

indicator light

changes from a slow to a rapidly blinking light. Now you may release
both the HomeLink

威

and hand-held transmitter buttons.

Note:

Some entry gates and garage door openers may require you to

replace Step 2 with procedures noted in the “Gate Operator and
Canadian Programming” in this section for Canadian residents.

3. Firmly

press, hold for five seconds and release

the programmed

HomeLink

威

button up to two separate times to activate the door. If the

door does not activate, press and hold the just-trained HomeLink

威

button and observe the indicator light.

•

If the indicator light

stays on constantly, programming is complete

and your device should activate when the HomeLink

威

button is pressed

and released.

2008 Sable

(mgo)

Owners Guide (post-2002-fmt)
USA

(fus)

Driver Controls

108

«
...
106
107
108
109
110
...
»

Summary of Contents for Sable 2008









































































































































































































































































































































Reviews:

No comments

Related manuals for Sable 2008

Brand: AA Products Pages: 6

Brand: Wallbox Pages: 7

Multiple G9F18 AU000

Brand: Genesis Pages: 3

SmartShot Automatic 12V 1.5 Amp 5 Stage

Brand: Yuasa Pages: 44

Brand: Chevrolet Pages: 412

XEBRA ZAPCAR Series

Brand: Zap Pages: 16

2000 Oldsmobile Intrigue

Brand: Oldsmobile Pages: 348

Brand: Motoalliance Pages: 5

Brand: Sagem Pages: 10

Brand: Z Flash Pages: 4

Brand: true-i Pages: 11

Brand: ROADGEAR Pages: 2

Brand: Yenkee Pages: 22

Brand: Opel Pages: 242

VIEWLINE TEMPERATURE GAUGES

Brand: VDO Pages: 5

Brand: Bestop Pages: 14

Brand: OEM Audio Pages: 21

928 GT - 1991 WIRE DIAGRAM

Brand: Porsche Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands