manualshive.com logo in svg

Mercury Sable 2008, Owner'S Manual

The Mercury Sable 2008 Quick Reference Manual is a comprehensive guide to help you make the most of your vehicle. This user-friendly manual provides detailed instructions and essential information about your car's features and maintenance. Download it for free at manualshive.com and enjoy hassle-free driving with your Mercury Sable 2008.

Share
Download
background image

Power door lock switch autolock enable/disable procedure

Before starting, ensure the ignition is in the 1 (LOCK) position and all
vehicle doors are closed. You must complete Steps 1–5 within 30 seconds
or the procedure will have to be repeated. If the procedure needs to be
repeated, wait a minimum of 30 seconds before beginning again.

1. Place the key in the ignition and
turn the ignition to the 3 (RUN)
position.

2. Press the power door unlock
control on the door panel three
times.
3. Turn the ignition from the 3 (RUN) position to the 1 (LOCK) position.
4. Press the power door unlock control on the door panel three times.
5. Turn the ignition back to the 3 (RUN) position. The horn will chirp
one time to confirm programming mode has been entered and is active.
6. To enable/disable the autolock feature, press the unlock control, then
press the lock control. The horn will chirp once if autolock was
deactivated or twice (one short and one long chirp) if autolock was
activated.
7. Turn the ignition to the 1 (LOCK) position. The horn will chirp once
to confirm the procedure is complete.

Keyless entry key pad autolock enable/disable procedure

1. Turn the ignition to the 1 (LOCK)
position.

2. Close all the doors.

3. Enter factory–set 5–digit entry
code.

4. Press and hold the 3

•

4. While

holding the 3

•

4 press the 7

•

8.

5. Release the 7

•

8.

6. Release the 3

•

4.

The user should receive a

horn chirp

to indicate the system has been

disabled or a chirp followed by a honk to indicate the system has been
enabled.

2008 Sable

(mgo)

Owners Guide (post-2002-fmt)
USA

(fus)

Locks and Security

125

Summary of Contents for Sable 2008









































































































































































































































































































































Reviews:

No comments

Related manuals for Sable 2008

Parrot CK 3000 Evolution Specifications preview
CK 3000 Evolution
Brand: Parrot Pages: 2
BMW Wireless Charging Station Universal Instructions For Use Manual preview
Wireless Charging Station Universal
Brand: BMW Pages: 160
Romik 2137 2D Installation Instructions Manual preview
2137 2D
Brand: Romik Pages: 6
Victory 4x4 5TH GEN 4RUNNER Install Instructions preview
5TH GEN 4RUNNER
Brand: Victory 4x4 Pages: 5
Keith WALKING FLOOR Helpful Hints preview
WALKING FLOOR
Brand: Keith Pages: 2
Haibang HA998 Series Installation Instructions Manual preview
HA998 Series
Brand: Haibang Pages: 6
Whipple TOMAHAWK V1 Instruction Manual preview
TOMAHAWK V1
Brand: Whipple Pages: 3
EUFAB 16458 Operating Instructions Manual preview
16458
Brand: EUFAB Pages: 16
Car-Systems Parktronic system Volkswagen Golf MK7 Assembly Manual preview
Parktronic system Volkswagen Golf MK7
Brand: Car-Systems Pages: 10
INDIWORK A-LINK2-NTG5 Instruction Manual preview
A-LINK2-NTG5
Brand: INDIWORK Pages: 18
Opel CORSA 2020 Infotainment Manual preview
CORSA 2020
Brand: Opel Pages: 103
v.link CI-VL2-PC-HSD Manual preview
CI-VL2-PC-HSD
Brand: v.link Pages: 19
BabySafe Beagle User Manual preview
Beagle
Brand: BabySafe Pages: 43
E-Lead EL-HA1 Manual preview
EL-HA1
Brand: E-Lead Pages: 11
RADICAL R-C10AD2 Device Installation Manual preview
R-C10AD2
Brand: RADICAL Pages: 11
Buick 2006 LaCrosse Getting To Know Manual preview
2006 LaCrosse
Brand: Buick Pages: 20
Altius ATHUDW-SCA User Manual preview
ATHUDW-SCA
Brand: Altius Pages: 16
Chevrolet 2012 Malibu Owner'S Manual preview
2012 Malibu
Brand: Chevrolet Pages: 376

Brands by name

Popular brands

Load more brands