Mercury Sable 2008 Owner'S Manual Download Page 53

Page: 53 / 328

Power control:

Press to turn the FES (Family Entertainment

System) ON/OFF.

Cursor controls:

Use in various active menus to advance the cursor

up/down/left/right. When not in a Menu, the left and right cursor controls
decrease and increase the display brightness.

DISPLAY:

Press to access the on-screen display of the FES functions

and adjustments.

RETURN:

Press to return to the previous menu screen.

ANGLE

(DVD dependent): Press to select the angle to view the

scene.

Channel A/B:

Press to select either A or B headphones and then use

the MEDIA control to select the desired playing media for the
headphones.

VOL (Volume):

When in Single Play, press to increase (

) or

decrease (

) the volume over all speakers. When in Dual Play, press to

increase (

) or decrease (

) the volume for the wired headphones.

2008 Sable

(mgo)

Owners Guide (post-2002-fmt)
USA

(fus)

Entertainment Systems

Summary of Contents for Sable 2008









































































































































































































































































































































Search results

Summary of Contents for Sable 2008

Reviews:

Related manuals for Sable 2008

Brands by name

Popular brands

Mercury Sable 2008, Owner'S Manual

Search results

Summary of Contents for Sable 2008

Reviews:

Related manuals for Sable 2008

Brands by name

Popular brands