Mercedes-Benz SL 320 Operator'S Manual Download Page 119

Page: 119 / 161

119

Replacing Bulbs

When replacing bulbs, install only 12

volt bulbs with the specified watt

rating.

When replacing halogen bulbs do not

touch glass portion of bulb with bare

hands. Use plain paper or a clean cloth.

Warning!

Halogen lamps contain pressurized

gas. A bulb can explode if you

•

touch or move it when hot,

•

drop the bulb,

•

scratch the bulb.

Bulb for Low Beam

(Xenon)

Warning!

Because of high voltage in Xenon

lamps, it is dangerous to replace the

bulb or repair the lamp and its

components. We recommend that

you have such work done by a

qualified technician.

Bulb for High Beam

H1 (55 W)

Open hood.

Depress latch (7) and remove

cover (6).

Pull off electrical connector (9).

Unhook clamping ring and remove

bulb.

Insert new bulb (seating properly in

cutouts of bulb socket), and mount

clamping ring. Reinstall and push

electrical connector on securely.

Reinstall bottom end of cover (6) and

push against top end of cover until

properly seated.

Check lamp for proper operation.

Turn Signal, Parking, Side

Marker and Standing Lamp

(2375 NA [28.5/8.3 W/ 30/2.2 cp] bulb)

Open hood.

Turn bulb socket (5) with bulb

counterclockwise and pull out. Push

bulb into socket, turn counterclockwise

and remove.

Insert new bulb in socket, push in and

twist clockwise. Reinstall bulb socket,

push in and twist clockwise.

Summary of Contents for SL 320


































































































































































Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands

Mercedes-Benz SL 320, Operator'S Manual

Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands